Lattice Semiconductor ECP5 Versa Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 86

background image

ECP5 and ECP5-5G High-Speed I/O Interface

Technical Note

© 2014-2020 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

FPGA-TN-02035-1.3

29

tCOMin = Data cannot transition BEFORE Min

tCOMax = Data cannot transition AFTER Max

tCOMin

CLK

DATA

tCOMax

Figure 5.18. tCO Min and Max Timing Analysis

5.13.3.1.

Transmit Centered Interfaces

In this case, the transmit clock is expected to be centered to the data when leaving the device.

shows the

timing for a centered transmit interface.

tDVBGDDR = Data valid before clock

tDVAGDDR = Data valid after clock

tU = Data transition

t

U

t

DVBCKGDDR

t

DVACKGDDR

t

DVACKGDDR

t

DVBCKGDDR

½ T

Target Edge

CLK

DATA

Figure 5.19. Transmit Centered Interface Timing

shows that max value after which the data cannot transition is – tVB_GDDR. The min value before which

the data cannot transition is – (tU+tVB_GDDR). Negative sign is used because in this particular case where clock is
forwarded centered aligned to the data these two conditions occurs before the clock edge.

ECP5 and ECP5-5G Family Data Sheet (FPGA-DS-02012)

specifies the tDVB_GDDRX1/X2 and tDVA_GDDRX1/X2

values at maximum speed. However, we do not have the tU value. Hence, min tCO can be calculated using the
following equation.

tCO Min = - (tVB_GDDRX1/X2 + tU)

½

T = tDVA_GDDRX1/X2 + tVB_GDDRX1/X2 + tU

- (tVB_GDDRX1/X2 + tU) = 1/2T - tDVA_GDDRX1/X2

tCO Min = 1/2T - tDVA_GDDRX1/X2

The clock to out time in the software can be specified as –

CLOCK_TO_OUT PORT “dataout” MAX <-tDVB_GDDRX1/X2> MIN <tDVA_GDDRX1/X2 -1/2 Clock Period> CLKPORT

“clk” CLKOUT PORT “clkout”;

where:

Data = Data Output Port

Clock = Forwarded Clock Output Port

clk = Input Clock Port

«
...
27
28
29
30
31
...
»

Содержание ECP5 Versa























































































Отзывы:

Нет отзывов

Похожие инструкции для ECP5 Versa

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: B-K lighting Страницы: 3

Бренд: jablotron Страницы: 2

Бренд: Jet Страницы: 12

Бренд: laerdal Страницы: 9

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: JBSYSTEMS Light Страницы: 17

i-Digits Access

Бренд: Össur Страницы: 231

Бренд: ubicquia Страницы: 4

Бренд: Elenco Electronics Страницы: 12

Бренд: GRAVITY Страницы: 2

Бренд: Wartmann Страницы: 56

Бренд: K-SPORT Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды