Lattice Semiconductor ECP5 Versa Скачать руководство пользователя страница 56

Страница: 56 / 86

ECP5 and ECP5-5G High-Speed I/O Interface

Technical Note

www.latticesemi.com/legal

All other brand or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.

FPGA-TN-02035-1.3

User Interface Option

Description

Values

Default

Actual Clock Frequency

Displays the achieved PLL output clock
frequency

Actual PLL output Frequency
achieved based on interface
requirement

—

CLKI Input Buffer Type

The I/O Standard for the PLL Reference
Clock

List of Legal Input Standards,
None (if coming from fabric)

LVCMOS25

Enable MIPI Filter Soft IP
for Low Speed Data

Generates the MIPI Filter soft IP in
module for Interface = Receiver MIPI

Enable, Disable

Disable

Table 7.4

shows how the interfaces are selected by Clarity Designer based on the selections made in the

Pre-Configuration tab.

Table 7.4. Clarity Designer DDR_Generic Interface Selection

Interface Type

Gearing Ratio

Alignment

Default Interface

Receive

2:1

Edge-to-Edge

GDDRX1_RX.SCLK.Aligned

Receive

2:1

Centered

GDDRX1_RX.SCLK.Centered

Receive

4:1

Edge-to-Edge

GDDRX2_RX.ECLK.Aligned

Receive

4:1

Centered

GDDRX2_RX.ECLK.Centered

Receive MIPI

4:1

Centered

GDDRX2_RX.ECLK.MIPI

Transmit

2:1

Edge-to-Edge

GDDRX1_TX.SCLK.Aligned

Transmit

2:1

Centered

GDDRX1_TX.SCLK.Centered

Transmit

4:1

Edge-to-Edge

GDDRX2_TX.ECLK.Aligned

Transmit

4:1

Centered

GDDRX2_TX.ECLK.Centered

Refer to the

High-Speed DDR Interface Details

section to see implementation details for each of these interfaces.

Содержание ECP5 Versa























































































Результаты поиска

Содержание ECP5 Versa

Отзывы:

Похожие инструкции для ECP5 Versa

Бренды по названию

Популярные бренды

Lattice Semiconductor ECP5 Versa, Техническая заметка

Результаты поиска

Содержание ECP5 Versa

Отзывы:

Похожие инструкции для ECP5 Versa

Бренды по названию

Популярные бренды