Edit. 03 - 06/2019
www.larius.eu
CH 200 AD
7
• ABSOLUTELY AVOID SPRAYING FLAMMABLE PRODUCTS
OR SOLVENTS IN CLOSED ENVIRONMENTS.
• ABSOLUTELY AVOID USING THE MACHINE IN ENVIRON
-
MENTS SATURATED WITH POTENTIALLY EXPLOSIVE
GASES
If the product flows at high speed through the
flexible tube static electricity may be created,
manifested with small shocks and sparks. The
machine should be electrically grounded. The
pump is grounded by the grounding wire of the
power cable. The spray gun is grounded via a high
pressure flexible tube. All the conductive objects
that are near the work area must be grounded.
Always verify the compatibility of the product with
the materials that make up the system
(pump, spray
gun, flexible tube and accessories)
with which it may
come into contact. Do not use paints or solvents
that contain halogenated hydrocarbons
(such
as methylene chloride)
. Products in contact with
aluminium parts of the machine may cause dan-
gerous chemical reactions with risk of explosion.
• TIGHTEN AND CHECK ALL THE CONNECTION FITTINGS
BETWEEN THE PUMP, THE FLEXIBLE TUBE AND THE
SPRAY GUN BEFORE USING THIS MACHINE.
• ALWAYS USE THE FLEXIBLE TUBE PROVIDED IN THE
STANDARD WORK KIT. THE USE OF ACCESSORIES OR
EQUIPMENT DIFFERENT THAN THOSE RECOMMENDED
IN THIS MANUAL MAY CAUSE INJURY.
• THE FLUID CONTAINED IN THE FLEXIBLE TUBE MAY BE
VERY DANGEROUS. HANDLE THE FLEXIBLE TUBE WITH
CARE. DO NOT PULL THE FLEXIBLE TUBE TO MOVE THE
MACHINE. NEVER USED A DAMAGED OR REPAIRED
FLEXIBLE TUBE.
IF THE PRODUCT TO BE USED IS TOXIC, AVOID
INHALATION AND ONLY HANDLE USING PRO-
TECTIVE GLOVES, PROTECTIVE GOOGLES AND
APPRORPIATE MASKS.
USE APPROPRIATE HEARING PROTECTION EQUIP-
MENT IF WORKING IN THE IMMEDIATE VICINITY
OF THE MACHINE.
Electrical safety regulations
•
Ensure the switch is in the “OFF” position before inserting
the power cable plug into the electrical outlet.
• Do not transport the machine if it is connected to the power
supply network.
• Disconnect the plug from the outlet if the machine is not in
use and before performing all maintenance or accessory
replacement operations.
• Do not drag the machine or disconnect the plug by pulling
on the power cable.
• Keep the cable away from heat, mineral oils and sharp
edges.
• If the machine is used outdoors, use a suitable extension
cord, that is intended and marked for outdoor use.
• To prevent injuries, repairs of electrical parts must only be
carried out by qualified personnel.
Never tamper with the calibration values of the
instruments.
PRECAUTIONS DURING WORK
•
Do not smoke, do not cause open flames.
•
Only the spray guns and the vehicles required for trans-
porting the powders must be in the booths: all other the
electrical devices must be outside the booth.
•
Ensure that suction capacity in the spray booth is sufficient
and that the powder does not accumulate in any part of
the booth.
•
Verify that the frames and all the electrical devices are
properly grounded.
•
Ensure the operator is correctly "grounded".
Do not use insulated gloves and plastic shoes. Antistatic
shoes are recommended.
•
Do not enter the spray booth when the machine is operat-
ing. Before entering, ensure the locking system of the entire
system is working properly.
•
Facial masks and protective suits are recommended, when
you need to work in environments filled with powder.
•
Keep the area surrounding the booth clean, for at least 5
metres.
•
Keep the lighting lamps clean. Wash hands and face before
eating or drinking.
HEALTH AND SAFETY
The powders:
•
Can cause irritation to the eyes, hands and respiratory
system, after prolonged direct contact.
•
Are toxic if inhaled.
•
Are not flammable, but they can cause combustion if their
concentration in the air exceeds the allowable limit.
•
Can form a conductor wire, that can be be switched on by
"open flames", heat or by electrical sparks.
