Lantronix SCS Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 424

background image

Additional Remote Networking

Increasing Performance

5-9

5.4.2 Compressing Data and Correcting Errors

The amount of data that can be transmitted at once (throughput) can be increased by using data compression.
Data compression enables a device such as a modem to transfer a larger amount of data at once. When
compression is used, uncompressed data arrives on the modem’s serial port and the modem compresses the
data before sending it over the phone line.

The disadvantage of compression is increased latency, the time required to transfer data from one place to
another. Compression increases latency due to the time required to compress the data before it is sent. Error
correction can also increase latency, as the data must be checked for integrity after it is received.

In situations where the delay is undesirable (for example, during interactive use over a long distance line),
compression and error correction should not be used. These options are enabled by default on the SCS; to
disable them, use the following commands:

Figure 5-16:

Disabling Error Correction and Compression

Note:

For a complete discussion of compression and error correction, see Chapter 9,
Modems.

5.4.3 Adding Bandwidth

Like compression, adding bandwidth can increase throughput. Sites can be configured to automatically
bring up additional connections when more bandwidth is needed, for example, when the amount of data to
be transmitted exceeds the bandwidth of the port.

How "aggressively" a site will add bandwidth can be controlled with two factors: the period during which
the use of bandwidth is measured, and the percentage at which bandwidth is added.

For example, to increase bandwidth for small or periodic increases in traffic, reduce the measurement time
period. A similar effect could be obtained by reducing the percentage utilization at which bandwidth is
increased. To require a sustained increase in traffic to increase bandwidth, the measurement time period and
the utilization percentage should be increased. See

Bandwidth On Demand

on page 5-4 for more

information.

5.4.4 IP Header Compression

Each site may be configured to compress the header information on IP (TCP only) packets before they are
forwarded. When a site is created, IP header compression will be enabled by default.

Header compression is most useful for interactive traffic such as Telnet sessions. Compressing the header
information for interactive traffic decreases the delay before data is transferred. In other words, if a key is
pressed during a Telnet session, the time required to echo that character back to the user’s terminal will be
reduced.

For more information on IP header compression, see

Header Compression

on page 6-8.

Local>> DEFINE PORT 2 MODEM ERRORCORRECTION DISABLED
Local>> DEFINE PORT 2 MODEM COMPRESSION DISABLED

«
...
81
82
83
84
85
...
»

Содержание SCS









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SCS

Бренд: Samsung Страницы: 7

Бренд: Aaeon Страницы: 38

SBXL52 - Server Compute Blade

Бренд: Intel Страницы: 126

Sun Fire X2100 M2

Бренд: Sun Microsystems Страницы: 128

Бренд: Velvac Страницы: 55

Netfinity Series

Бренд: IBM Страницы: 44

Бренд: NetMedia Страницы: 2

Бренд: Olive Страницы: 19

BocaVision WT120

Бренд: Boca Systems Страницы: 28

SuperServer E301-9D-8CN8TP

Бренд: Supermicro Страницы: 117

Бренд: Brocade Communications Systems Страницы: 176

AND-APL1E Series

Бренд: Acrosser Technology Страницы: 42

Бренд: Asus Страницы: 98

Бренд: Asus Страницы: 84

EMC VxFlex Appliance R840

Бренд: Dell Страницы: 44

EqualLogic PS4000

Бренд: Dell Страницы: 73

EMC PowerProtect DD6400 System

Бренд: Dell Страницы: 46

EqualLogic PS5500

Бренд: Dell Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды