Lantronix SCS Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 424

background image

PPP

NCP

7-3

On incoming connections, the port’s CHAP or PAP configuration will be used to determine the
authentication required for the connection. For example, if a remote node was logged into port 2 on the SCS
and port 2 was configured to use PAP to authenticate remote hosts, the remote node would be prompted to
authenticate itself.

Outgoing connections use the site’s CHAP or PAP configuration. For example, if site

irvine

, which has

CHAP enabled, initiated an outgoing connection to a remote router, and the remote site required the SCS to
authenticate itself using CHAP, the SCS would offer its username and password to the remote site.

Use caution with CHAP/PAP authentication because configuring both a local and a remote password on the
same site could compromise security. If a site with both local and remote passwords defined receives an
incoming call, during the LCP negotiation process the site will say that it is willing to transmit both
passwords. The passwords will not be automatically transmitted, but the site will let the user know that it is
willing to do so if required. If the user requires the SCS to authenticate itself, the SCS will transmit the
remote password over the link, thereby give the user a password to access the server.

Note:

For a complete description of authentication, refer to Chapter 11, Security.

7.1.5 CBCP

The SCS supports the Microsoft Callback Control Protocol (CBCP) for dial-in PPP clients that request it.
In conjunction with the CBCP, you can configure the SCS to allow the PPP client to choose a dialback
telephone number to reverse phone charges.

For more information, see

Dialback Using CBCP

on page 11-7.

7.2 NCP

Network Control Protocols (NCPs) govern use of a specific network protocol over the PPP link. On the SCS,
PPP uses the IP protocol. PPP uses the IP Control Protocol (IPCP) to negotiate the use of IP over a link.
IPCP allows for dynamic address assignment and Van Jacobson TCP header compression.

Note:

IP over PPP is described in RFC 1332. Van Jacobson TCP compression is
covered in RFC 1144.

If, during the negotiation process, the SCS receives a request for more IP compression slots than are
configured on the site (using the

Define Site IP Slots

command), the SCS will NAK (negative

acknowledge), and request the number of slots configured on the site.

7.3 Starting PPP

PPP can be started in a number of ways. For a detailed discussion of the PPP startup sequence, see

Starting

PPP/Slip for Incoming Connections

on page 4-11 and

Using Sites for Outgoing Connections

on page 4-6.

«
...
118
119
120
121
122
...
»

Содержание SCS









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SCS

System x3100 M4

Бренд: IBM Страницы: 332

Бренд: SEH Страницы: 5

UltraNEXUS-HD Flex

Бренд: Leightronix Страницы: 5

SC450NX - Server Platform - 0 MB RAM

Бренд: Intel Страницы: 200

SuperServer 5013G-M

Бренд: Supero Страницы: 104

ConnectPort LTS 16

Бренд: Digi Страницы: 169

Бренд: Hitachi Страницы: 208

Бренд: Hitachi Страницы: 36

Бренд: Intergraph Страницы: 102

Бренд: EVS Страницы: 70

Бренд: Certon Страницы: 29

Бренд: ClearCube Страницы: 5

Бренд: Measurement Computing Страницы: 56

Бренд: Xantech Страницы: 52

STRATOS S910 Series

Бренд: QCT Страницы: 41

Бренд: Rittal Страницы: 16

Бренд: AMX Страницы: 35

MAP-9101-10 Series

Бренд: decrane aerospace Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды