9J577-0822
3-7
Transport
1. Check and follow all federal, state, and local
requirements before transporting the Pulvi-Mulcher.
2. The Pulvi-Mulcher should be transported only by
tractor required for field operation. The implement
weight should not exceed more than 1.5 times the
tractor weight. Maximum transport speed for the
Pulvi-Mulcher is 20 mph for the implement and is
designated on the speed identification symbol located
on the front of the implement.
CAUTION
3. When towing equipment in combination, the maximum
equipment ground speed shall be limited to the lowest
specified ground speed of any of the towed implements.
4. Maximum transport speed shall be the lesser of travel
speed specified in the operator's manual, speed
identification symbol, information sign of towed
equipment, or limit of road conditions.
5. Slow down when driving on rough roads. Reduce
speed when turning, or on curves and slopes to avoid
tipping. Equipment altered other than the place of
manufacture may reduce the maximum transport
speed. Additional weight, added tanks, harrowing
attachments, etc. may reduce implement load
carrying capabilities.
6. A Safety Chain is provided with the implement to
insure safe transport.
• The Safety Chain should have a tensile strength
equal to or greater than the gross weight of the
implement. The chain is attached to the lower hitch
clevis hole with two Flat Washers between the
clamp plates to assure a tight connection. Always
use a 1" diameter Grade 8 bolt for this connection.
• Attach the Safety Chain to the Tractor Drawbar.
Provide only enough slack in the chain for turning.
Do not use an intermediate chain support as the
attaching point for the chain on the tractor. Do not
pull the implement by the Safety Chain.
• Regularly inspect the Safety Chain for worn,
stretched, or broken links and ends. Replace the
Safety Chain if it is damaged or deformed in any way.
7. Check that tires are of proper size, load rating, and
inflated to manufacture specifications before
transporting. Check wheel lug bolts to ensure tightness.
8. Know the transport heights and widths of the unit
before transporting. Use caution when transporting
near bridges and power lines.
WARNING
9. Raise the machine to full transport height.
10. Install transport locks on lift systems. Do not depend
solely on implement hydraulics for transport.
WARNING
11. Transport during daylight hours when ever possible.
Always use flashing warning lights, except where such
use is prohibited by law. Make sure lights, reflectors
and SMV emblem are clearly visible and operating.
Remove any obstructions such as dirt, mud, stalks or
residue that restricts view before transporting.
Figure 3-6: Rockshaft and Drawbar Transport Locks
in Locked Position
Excessive speed may result in loss of control of
the tractor and implement, reduced braking
ability, or failure of the implement tire or structure.
Do not exceed the implement maximum specified
ground speed regardless of the capability of the
maximum tractor speed.
Electrocution can occur without direct contact.
Failure to use transport lock pins during transport
may result in permanent equipment damage,
serious injury or death.
Transport Lock Pin
LOCKED
Position
Transport
Lock
Cylinder
Clevis Pin
Hair Pin
Transport
Axle
Frame
Flat Washer
Drawbar
Hair Pin
Tie Bar
Clevis Pin
Cylinder
Side Plate
Transport Lock Pin
LOCKED
Position
Flat Washer
Flat
Washer
Содержание Brillion WCC
