Landoll 825A Скачать руководство пользователя

Страница: 65 / 70

BRAKES (CONTINUED)

SYMPTOM

PROBLEM: REMEDY

ALL BRAKES DO NOT RELEASE

Air system improperly connected to tractor:

tighten or

adjust connections.

Brake valve on tractor is applied:

release brake.

Relay emergency valve in emergency position:

check line

pressure and check valve.

Restricted tubing or line:

locate restriction and remove.

Defective tractor protection valve:

troubleshoot tractor air sys-

tem.

Parking brakes locked:

troubleshoot air system.

Moisture in air system:

Check air system

Tractor pressure too low:

Adjust to provide 105 psi min.

INSUFFICIENT BRAKES

Brakes need adjusting:

adjust brakes.

Brakes need lubricating:

lubricate brakes.

Brakes need relining:

reline brakes.

Low air pressure:

troubleshoot air system.

Defective relay emergency valve:

repair or replace.

Brakes overheated:

stop and allow brakes to cool, locate

cause of overheating.

BRAKES GRABBING

Grease on brake linings:

reline brakes.

Brake rigging binding:

align brakes or replace bent parts.

Defective brake valve on tractor:

repair or replace valve.

Defective relay emergency valve:

repair or replace valve.

EXCESSIVE LEAKAGE WITH

BRAKES RELEASED

Relay emergency valve leaking:

repair or replace valve.

Leaking tubing or hose:

replace defective part.

EXCESSIVE LEAKAGE WITH

BRAKES APPLIED

Relay emergency valve leaking:

repair or replace valve.

Leaking brake chamber diaphragm:

replace diaphragm.

Call Factory or see qualified Trailer/Brake Technician

Leaking tubing or hose:

replace defective part.

EXCESSIVE LEAKAGE WITH

EMERGENCY SYSTEM ONLY

APPLIED - NO LEAKAGE WITH

NORMAL BRAKING

Defective relay emergency valve:

repair or replace valve.

EXCESSIVE WATER PRESENT IN

BRAKE SYSTEM

Reservoir not drained often enough:

drain reservoir daily.

EXCESSIVE OIL PRESENT IN

BRAKE SYSTEM

Compressor on tractor passing excessive oil:

repair compres-

sor.

BRAKE WILL NOT APPLY

PROPERLY

Flat spot on cam roller or camshaft:

replace and lubricate.

5-5

Содержание 825A







































































Результаты поиска

Содержание 825A

Отзывы:

Похожие инструкции для 825A

Бренды по названию

Популярные бренды

Landoll 825A, Руководство оператора

Результаты поиска

Содержание 825A

Отзывы:

Похожие инструкции для 825A

Бренды по названию

Популярные бренды