Landoll 825A Скачать руководство пользователя

Страница: 56 / 70

Insert bearing cups into the hub.

Clean the mounting surfaces with a good

grade commercial cleaner and soft rag. Dry

all component parts with a clean, absorbent

cloth or paper. Lubricant will not adhere to

surfaces wet with solvent.

Install inner bearing, cone, and seal.

IMPORTANT

DO NOT MIX NEW CUPS WITH OLD CONES OR

NEW CONES WITH OLD CUPS.

Place the hub or wheel over the axle spindle

being careful to align the hub bore with the

axle. Do not damage the seal. Support the

hub assembly until the outer bearing cone

and spindle nut are installed, to avoid damag-

ing the seal.

Install the outer bearing cone and inner

spindle nut, tightening the nut until it is snug

against the outer bearing cone. Remove the

hub support allowing the hub to rest on the

bearings.

Install and adjust bearings

(See Section

4-10, Wheel Bearing Lubrication and Ad-

justment).

Install the hub cap with the proper gasket.

Tighten the cap screws of the hub cap to 15

to 20 ft-lbs. of torque.

Remove the filler plug and fill the hub cavity

to the recommended level with a gear type

oil.

Place the drum over the hub and brake

shoes being careful not to damage the

threads on the studs. Make sure the drum

seats flat against the hub flange and mates

properly with the hub pilot. There should be

no interference between the brake drum pilot

chamfer and the corner radius on the hub. If

interference exists, the hub will not be able to

function properly.

4-22

Figure 4-14 Outboard Mount Hub and Drum

Содержание 825A







































































Результаты поиска

Содержание 825A

Отзывы:

Похожие инструкции для 825A

Бренды по названию

Популярные бренды

Landoll 825A, Руководство оператора

Результаты поиска

Содержание 825A

Отзывы:

Похожие инструкции для 825A

Бренды по названию

Популярные бренды