Landoll 825A Скачать руководство пользователя

Страница: 61 / 70

TROUBLESHOOTING

Troubleshooting should be performed by a trained and competent technician. Landoll Corporation is not

responsible for equipment that is improperly maintained. Contact an authorized Landoll Service center or

the Landoll factory for servicing.

5-1 ELECTRICAL

Most electrical system problems show up as a burned out light or fuse, or inoperative electrical compo-

nent. Wiring, grounds, or components may be at fault. Locate the symptom in this section that best identi-

fies your electrical problem. Check out each possible problem under that symptom. If the problem cannot be

located, see an automotive electrical specialist.

SYMPTOM

PROBLEM: REMEDY

NO LIGHTS

Fuse blown:

replace fuse.

Connection at plug-in:

tighten connection.

Broken or corroded wires:

replace wire.

Ground wire loose:

clean and tighten ground.

LIGHTS FLICKERING

Wires shorted or loose:

locate, insulate, replace, or tighten.

Grounding through fifth wheel:

locate broken ground wire (tractor

or semitrailer).

LIGHTS DIM

Voltage difference between semitrailer & tractor:

match bulbs

with tractor voltage.

Grounding through fifth wheel:

locate broken ground wire (tractor

or semitrailer).

LIGHTS BRIGHT & BURN OUT

Voltage difference between semitrailer & tractor:

match bulbs

with tractor voltage.

FUSE BLOW-OUT OR CIRCUIT

BREAKER TRIPPING

Vibration:

locate source of vibration and repair.

Short circuit:

replace fuse and try all accessories. If fuse blows

right away, locate short and repair.

LAMP BULB BURN OUT

Vibration:

locate source of vibration and repair.

Short circuit:

replace fuse and try all accessories. If fuse blows

right away, locate short and repair.

Loose connection:

check lamp sockets and ground connections.

Intermittent short:

locate short and repair.

Improper voltage:

check voltage regulator output.

5-1

Содержание 825A







































































Результаты поиска

Содержание 825A

Отзывы:

Похожие инструкции для 825A

Бренды по названию

Популярные бренды

Landoll 825A, Руководство оператора

Результаты поиска

Содержание 825A

Отзывы:

Похожие инструкции для 825A

Бренды по названию

Популярные бренды