Landoll 825A Скачать руководство пользователя страница 39

Страница: 39 / 70

Scrape, sand, prime, and repaint areas

where finish is missing or where there is evi-

dence of corrosion.

Replace any missing or illegible decals. Re-

place any missing or damaged reflective tape.

Use Troubleshooting Guide to check for

“SYMPTOMS” AND “PROBLEMS” of any

semitrailer system not functioning correctly, or

where wear, distortion, or breakage can be

found. Administer “REMEDY” according to

right-hand column of Troubleshooting guide.

After disassembling any components, thor-

oughly clean dirt and old lubricant from all

parts. Do not use a wire brush on any bearing

parts or surfaces — use a stiff bristle brush.

Do not use compressed air, or spin bearing

parts when cleaning. These practices can

throw solvents, dirt, or metal particles into

your eyes. Dry clean parts with lint free,

clean, soft, absorbent, cloth or paper. Wash

and dry hands.

Inspect seals, seal wiping surfaces, bearing

caps, and bearing cones for wear, pitting,

chipping, or other damage.

4-3 GOOSENECK, FRAME, AND DECK

4-3.1

Repairing Structural Defects

If any structural defect is found, the fault must

be corrected before further use of the vehicle. To

continue usage could endanger the trailer, its load,

personnel, traffic, and properties. If any cracks or

breaks are found, contact the Landoll factory for

repairs. Inspect the deck daily for broken or miss-

ing planks or missing attachments. Replace any

defective parts promptly.

4-4 HYDRAULIC SYSTEM

4-4.1

General

Check the oil level of the tractor wet kit

weekly, or after any leakage. See

Table 4-1

for proper hydraulic oil. Check the hydraulic

oil level with hydraulic cylinders in the re-

tracted position and the hydraulic pump dis-

engaged. Enough volume in tank (approxi-

mately 15 gallons) above hydraulic oil level

must be available to accept extra oil from cyl-

inders when retracted.

Overfilling can cause hydraulic fluid over-

flow during operation.

Hydraulic system pressure relief valves

should be set at 2500 psi.

Check hoses weekly for cracks or leaks. If a

valve or line leaks, it should be replaced im-

mediately.

4-5

Содержание 825A







































































Результаты поиска

Содержание 825A

Отзывы:

Бренды по названию

Популярные бренды

Landoll 825A, Руководство оператора

Результаты поиска

Содержание 825A

Отзывы:

Бренды по названию

Популярные бренды