4-2
F-1130-2304
Tractor Preparation
The Landoll 2411 Weatherproofer designed to be pulled
by tractor equipped with a double lip or clevis type hitch.
If your tractor is not equipped as such, you need to
purchase the hitch from your local tractor dealer. If your
Weatherproofer equipped with the clevis option, this
should be removed. The clevis option is only for transport
use. Before attaching the Weatherproofer, prepare the
tractor as follows:
1.
Inflate the rear tractor tires equally and add ballast
according to the tractor operator’s manual.
2.
Lock the tractor drawbar in the center position.
Weatherproofer Preparation
1.
Prior to operating the 2411 Weatherproofer, inspect it
thoroughly for good operating condition.
2.
Replace worn or missing parts.
3.
When the machine is new, check the bolt tightness
after a few hours of operation. Tighten any loose nuts
or bolts. Check the gauge wheel lug bolts daily.
4.
Check the lift wheel tire inflation. Inflate all tires
equally
to
avoid
side
draft.
Follow
the
tire
manufacturer’s recommended pressures listed on the
sidewall of the tires.
5.
Check disc scrapers for proper adjustment to the disc
blade
a.
Loosen U-bolts. Slide scraper assembly to adjust
clearance to 1/8" to 1/4".
Figure 4-1: Disc Scraper Clearance to Disc Blade
IMPORTANT
Under certain conditions, it may be beneficial to set
scrapers as much as 1" away from the discs.
6.
Lubricate the machine as shown in
Maintenance” on page 5-2 and See Figure 5-3
Attaching To The Tractor
1.
Align the tractor drawbar with the machine. Raise or
lower the disc ring hitch, as needed, using the swivel
jack. Attach the unit with proper size hitch pin.
2.
Always place the swivel jack on the interior mount
before setting the machine in motion.
3.
Clean all hydraulic couplings and attach to the tractor.
4.
Fully extend the hydraulic lift wheel cylinders, and
place the cylinder lockouts in the transport lock
position over the cylinder rods. Secure the lockouts
with the lockout pins.
5.
Attach safety chain to tractor allowing plenty of
movement for turning both directions. The safety
chain should latch securely to prevent it coming loose.
6.
Plug in the 7-pin connector for the lights.
a.The tractor should have a good clean receptacle,
free of dirt and corrosion.
b.Make sure the 7-pin connector is inserted all the
way in, and allows the cover to latch over the keyway
to secure it in place.
NOTE
The lighting system requires a good ground
connection and if the lights do not seem to work right
check the installation of the 7-pin connector and the
condition of the pins.
1/8”
Содержание 2411
