4-12
F-1130-2304
Disc Lev/Hyd Flat RL Adjust-
ments
1.
The
optional
Disc
Leveler/Hydraulic
Flat
Reel
attachment consists of independent disc assemblies
that are meant to cover the shank tracks with soil and
then a reel assembly that firms up the soil
2.
The disc leveler assemblies are independent of the
reels allowing them to be adjusted to the operators
preference. The hydraulic reels are equipped to either
be up or down, they are not to be run in float.
WARNING
3.
When starting out it is recommended to have the disc
leveler assemblies raised completely up. Once the
machine depth is obtained, then start lowering the
discs until the desired finish is achieved.
NOTE
The discs are not meant to be run deep creating
trenches, they are only intended to be a finishing tool.
4.
Each individual disc can be adjusted to 3 different
angle settings to allow more or less soil movement
. To adjust them, loosen the front
3/4 x 5 bolt, and remove the rear 3/4 x 5 bolt to rotate
the mount either direction. The discs are in the middle
position when shipped from the factory. Ground
speed and depth will both change how the finish
looks, they will have to be adjusted accordingly.
Figure 4-15: Individual Disc Angle Adjustment
NOTE
Model 2411-06 uses 1 set of 1P332 cylinder stops and
Models 2411AFG-07-09 uses 2 sets.
5.
Cylinder stops have been provided to maintain depth
position. With the cylinder stops installed, the leveler
will still be able to fully raise for transport.
for the cylinders to place the cylinder
stops on.
IMPORTANT
The 2411-7/9 shank machines must have the same
cylinder stops on each cylinder or the connecting
tube will be twisted when they are lowered if they do
not stop together.
6.
Periodically fully raise the disc leveler and rephase
the cylinders to keep them all in unison.
7.
The reel assembly down pressure spring is preset at
21-1/2”, if more or less pressure is needed the
cylinder rod may be turned inside the spring to adjust
this length
. Adjust the cylinders as
follows, loosen up the jam nut against the spring,
loosen the set screw in the end casting of the spring,
and using the wrench flats on the cylinder the reel
may be lowered or raised as needed. Then re-tighten
the set screw and jam nut. The reel may be ran fully
raised if needed to prevent plugging in adverse
conditions.
8.
Both the individual disc blades and the reel bearings
are maintenance free.
Know and verify actual implement height and
width before transporting. Attachments may
increase the overall height and width of the
implement. Use caution when transporting near
power lines. Electrocution can occur without
direct contact.
3/4 X 5 BOLTS
ANGLE ADJUSTMENT
SLOT
INDIVIDUAL
DISC MOUNT
Содержание 2411
