Landoll 2411, Руководство оператора

Страница: 36 / 116

3-2 F-1130-2304
TABLE OF CONTENTS
Center Frame and Lift Assembly
2411-06
IMPORTANT
Read all safety precautions at the front of the section
before attempting any of the following procedures.
WARNING
1. Place center frame weldment RT/LT assemblies on
stands approximately 36” high. The assembly area
should be a large level area of sufficient size to
accommodate
the Weatherproofer when fully
assembled See Figure 3-1 . RT and LT is determined
from standing at the back looking forward.
NOTE
The spring/clamp shank assemblies are installed at
the factory on center frames, center shank mount and
shank extension RT/LT. mount assembly.
2. Attach the center frame mount assembly between
center frame weldment RT/LT assemblies, secure
with 3/4 x 7, 3/4 x 2-1/2 bolts, 3/4 flat washers and 3/4
lock nuts. The LT rear upper 2 bolts have a 1/4” thick
flat washer on bolt head side.
3. Attachfront bolt plates, DCV/Hose mount plate with
7/8 x 7 GR8 bolts, 7/8 flat washers and 7/8 lock nuts.
4. Attach center bolt plates, hose tube support plate
using 7/8 x 10 GR8 bolts, 7/8 flat washers and 7/8
lock nuts.
5. Attach center bolt plate, rear bolt plate using 7/8 x 7
GR8 bolts, 7/8 x 6 GR8 bolts, 7/8 flat washers and 7/8
lock nuts.
6. Attach the shank ext mount assemblies on outside of
center frame weldment RT/LT assemblies, secure
with 3/4 x 7-1/2, 3/4 x 2-1/2 bolts, 3/4 flat washers and
3/4 lock nuts.
7. Attach the RT/LT light bracket assemblies with yellow
reflectors to front of machine on outside of center
frame weldment RT/LT assemblies, secure with 1/2 x
3-1/2 bolts, 1/2 flat washers and 1/2 lock nuts.
8. Install the transport locks to the light brackets with the
l-pin and hairpin clip.
9. Slide the rear of the hose support tube into the hose
tube support plate, secure the front of tube to the top
of the DCV/hose mount plate using 1/2 x 3 square
bolts and 1/2 lock nuts. Attach the hose clamps to the
top of tube using 3/8 x 5 bolts, 3/8 flat washers and 3/8
lock nuts.
10. Remove any shank assemblies that have been turned
around or mounted inside the frame for shipping, and
reposition,
See Figures 2-2 through See
Figures 2-4 for shank placement.
NOTE
All lifts and hubs/spindle come already assembled
from the factory.
11. Install a UHMW bearing between all 4 inner bearing
locators around the center lift assembly See
Figure 3-2 .
12. Insert a UHMW bearing into each bearing cap and
install the cap and bearing over the end of center lift
assembly.
13. Raise the center lift assembly into the center frame
and attach each end bearing cap to the center frame
with 3/4 x 2-1/2 bolts and 3/4 lock nuts
14. Install 2 inner lift bearing mounts with 3/4 x 2 bolts and
3/4 lock nuts.
NOTE
Make sure the center lift will rotate freely in the center
frame after it is assembled.
NOTE
Be sure the 4, 1-5/8 x 1-1/4 x 1 bushings are installed
in the lift plate mounts and center lift assembly mount
plates
See Figures 3-2 .
15. The base end of 4-1/2 x 16 cylinders attach to plate
on center frames, rod end attach to the plate on
center lift assembly.
16. Attach the depth control plates to back of center lift
with 1/2 x 2 bolts and 1/2 lock nuts. Install a 1 x .640
x 5/8 bushing in the depth stop assembly plate align
hole of plate with front top hole of depth control plates,
install a 1 x .640 x 5/8 bushing between top rear of
plates secure with 5/8 x 2 bolts and 5/8 lock nuts.
17. Attach the front of the depth stop assembly to front of
center frame assembly bracket with slide plate
between bracket and depth stop assembly, depth
stop guide on top, limit valve on bottom of bracket with
plunger to rear of machine, secure with 5/16 x 5-1/2
bolts and 5/16 lock nuts.
18. Install the tire/wheel assemblies to all hub/spindle
assemblies.
Do not attempt to lift heavy parts (such as the
frame, disc gangs, wheel lift, and pull hitch)
manually. Use a hoist or a forklift to move these
parts into position.