Land Pride RC4614 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 66

background image

Table of Contents

©

Copyright 2020 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

7/30/20

RC4614 & RCM4614 Rotary Cutters 331-937M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol   . . . . . . . . . . . . . 1
Safety Labels  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . 12
Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . 12

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Section 1: Assembly & Set-up . . . . . . . . . . . 13

Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . 13

Electrical Outlet . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hydraulic Outlets . . . . . . . . . . . . . . . . . . . . . . . . 13

Before You Start  . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . 13
Hitch Types  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Hitch Assembly  . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Park Jack Assembly  . . . . . . . . . . . . . . . . . . . . . . . 15
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . 15
Standard Clevis Hitch Hook-up  . . . . . . . . . . . . . . . 16
LP Performance Hitch Hook-up . . . . . . . . . . . . . . . 17
Bar-Tite Hitch Hook-up  . . . . . . . . . . . . . . . . . . . . . 18
Rephasing Lift Cylinders & Plumbing   . . . . . . . . . . 19
Wing Folding Cylinder & Plumbing  . . . . . . . . . . . . 19
Hydraulic Hook-up   . . . . . . . . . . . . . . . . . . . . . . . . 20
Remove Shipping Crossbar   . . . . . . . . . . . . . . . . . 21
Unfold Wing Deck  . . . . . . . . . . . . . . . . . . . . . . . . . 21
Relocate Wing Lift Cylinder Mount   . . . . . . . . . . . . 22
Driveline Installation  . . . . . . . . . . . . . . . . . . . . . . . 23
Driveline Hook-up to Tractor  . . . . . . . . . . . . . . . . . 24
Adjust Driveline Hanger   . . . . . . . . . . . . . . . . . . . . 24
Driveline Clearance Check  . . . . . . . . . . . . . . . . . . 25
Purge Hydraulic System  . . . . . . . . . . . . . . . . . . . . 25
Hook-up LED Lights   . . . . . . . . . . . . . . . . . . . . . . . 26
Unhook Rotary Cutter  . . . . . . . . . . . . . . . . . . . . . . 27

Section 2: Adjustments . . . . . . . . . . . . . . . . . 30

Park Jack Angle Alignment . . . . . . . . . . . . . . . . . . 30
Level Cutter Decks . . . . . . . . . . . . . . . . . . . . . . . . 30

Center Deck Leveling . . . . . . . . . . . . . . . . . . . . . 30
Wing Deck Leveling . . . . . . . . . . . . . . . . . . . . . . 31

Cutter Height Adjustment . . . . . . . . . . . . . . . . . . . 32
LP Performance Hitch Hole Size . . . . . . . . . . . . . . 32

Section 3: Operating Instructions . . . . . . . . 33

Startup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . 33
Avoid Extreme Turning Angles . . . . . . . . . . . . . . . 34
Tractor & Cutter Inspection . . . . . . . . . . . . . . . . . . 35

Blade Operation Inspection  . . . . . . . . . . . . . . . . . . 35
Transport Lock   . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Road Side Cutting  . . . . . . . . . . . . . . . . . . . . . . . . . 37
Field Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Inspect Field and Cutter Blades  . . . . . . . . . . . . . 37
Lower Wing Down & Set Cutting Height  . . . . . . . 37
Set Wing Folding Lever In Float Position  . . . . . . 37
Rephasing Out Of Phase Lift Cylinders   . . . . . . . 37
Select Gear Range . . . . . . . . . . . . . . . . . . . . . . . 38
Engage Blades . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Disengage Blades   . . . . . . . . . . . . . . . . . . . . . . . 38

General Operating Instructions . . . . . . . . . . . . . . . 39

Section 4: Options & Accessories . . . . . . . . . 40

Safety Guard Options   . . . . . . . . . . . . . . . . . . . . . . 40
Tire & Axle Options  . . . . . . . . . . . . . . . . . . . . . . . . 40
Hitch Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Selector Control Valve Kit  . . . . . . . . . . . . . . . . . . . 40

Section 5: Maintenance & Lubrication . . . . . 41

General Maintenance Information  . . . . . . . . . . . . . 41
Tractor Maintenance  . . . . . . . . . . . . . . . . . . . . . . . 41
Tire Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 42
Drivelines With Slip Clutches . . . . . . . . . . . . . . . . . 43
Gearbox Shaft Guard   . . . . . . . . . . . . . . . . . . . . . . 46
Skid Shoes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 48
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 48
Lubrication Points  . . . . . . . . . . . . . . . . . . . . . . . . . 49

Axle Hub Bearing  . . . . . . . . . . . . . . . . . . . . . . . . 49
Center Axle Pivots  . . . . . . . . . . . . . . . . . . . . . . . 49
Wing Axle Pivot   . . . . . . . . . . . . . . . . . . . . . . . . . 49
Hitch Frame  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Bar-Tite Hitch (Optional)   . . . . . . . . . . . . . . . . . . 50
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Divider Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
CV Main Driveline Profile Tubes . . . . . . . . . . . . . 52
CV Main Driveline Joints   . . . . . . . . . . . . . . . . . . 52
Wing Driveline Profile Tubes   . . . . . . . . . . . . . . . 54
Wing Driveline Joints  . . . . . . . . . . . . . . . . . . . . . 54
Intermediate Driveline Joints   . . . . . . . . . . . . . . . 54

Section 6: Specifications & Capacities  . . . . . 55
Section 7: Features & Benefits   . . . . . . . . . . . 57
Section 8: Troubleshooting  . . . . . . . . . . . . . . 58
Section 9: Torque & Tire Inflation Charts  . . . 59
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 60

«
1
2
3
4
5
...
»

Содержание RC4614



































































Отзывы:

Нет отзывов

Похожие инструкции для RC4614

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: Makita Страницы: 10

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: Rapid Technic Страницы: 152

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: Garmin Страницы: 20

Бренд: tayco Страницы: 111

Бренд: Ultraflex Страницы: 3

Бренд: Kärcher Страницы: 88

Бренд: Yamaha Страницы: 31

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды