Land Pride RC4614 Скачать руководство пользователя страница 22

Страница: 22 / 66

Section 1: Assembly & Set-up

Table of Contents

7/30/20

RC4614 & RCM4614 Rotary Cutters 331-937M

Bar-Tite Hitch Assembly to Tractor Drawbar

Figure 1-12

Bar-Tite Hitch Hook-up

Refer to Figure 1-12:

Attach Bar-Tite Hitch to Tractor Drawbar

1. Insert 1" x 5 1/2" hex bolt (#1) through hitch top

plate (#2), hitch bushing (#3), hitch wear plate (#4),

tractor drawbar (#5), and washer (#6) as shown.

Secure with 1" locknut (#7). Tighten 1" locknut snugly

to remove all play and then back nut

one-quarter turn.

Do Not

torque 1" locknut.

2. Insert two 3/4" x 6" GR5 hex bolts (#8) through,

3/4" flat washers (#9), hitch top plate (#2), hitch wear

plate (#4), and formed hitch support (#10) as shown.

Secure with 3/4" locknuts (#11).

3. Tighten 3/4" locknuts to correct torque.
4. Remove 1" x 6 1/2" GR5 hex bolt (#12) and 1" lock

nut (#13) from hitch bushing (#3). Keep hardware.

Attach Tractor to Rotary Cutter

Refer to Figure 1-13:

WARNING

To avoid serious injury or death:

•

Lightweight tractors with rear attached implements may

need weights added to the front to maintain steering control.

Consult your tractor Operator’s Manual to determine

proper weight requirements and maximum weight

limitations.

•

The ball detent pin must be fully inserted into the park jack

with ball visible and popped out on the far side of the jack

before working on or around an unhooked cutter.

1. Make certain park jack (#3) is properly attached to

cutter and secured with ball detent pin (#8).

22265

Tractor Hook-up to Bar-Tite Hitch

Figure 1-13

2. Store center 3-point link in the tractor’s storage hook.
3. Start tractor, raise 3-point arms fully up, and carefully

back tractor within close proximity of clevis (#9).

4. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 15.

5. Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

dimensions on page 13.

6. Raise or lower park jack (#3) to align hitch (#11) with

bolt hole in swivel clevis (#9).

Restart tractor and continue to back tractor up to

cutter hitch until hole in hitch bushing (#11) aligns

with holes in swivel clevis (#9).

8. Shut tractor down properly before dismounting.
9. Insert 1" x 6 1/2" GR5 hex bolt (#1) through swivel

clevis (#9) and hitch bushing (#11). Secure hex bolt

with locknut (#2). Tighten locknut snugly to remove

all play.

Do Not

torque 1" locknut.

10. Lower park jack (#3) until cutter hitch weight is

supported by tractor drawbar.

11. Remove park jack (#3) from hitch and attach it to the

weight box storage base with ball detent pin (#8).

Make sure the base is level with or lower than the

head. See cover picture for correct positioning.

12. Attach hitch safety chain (#4) to tractor. Adjust chain

length to remove all slack except what is necessary

to permit turning. Securely lock chain hook to the

safety chain.

13. Continue with

“Rephasing Lift Cylinders &

Plumbing”

on page 19.

33870

IMPORTANT:

Before moving the cutter, relocate

park jack by storing it on the left wing deck. Make

sure the jack is stored with its base level or lower

than the head to prevent water and freeze damage.

Содержание RC4614



































































Результаты поиска

Содержание RC4614

Отзывы:

Похожие инструкции для RC4614

Бренды по названию

Популярные бренды

Land Pride RC4614, Руководство оператора

Результаты поиска

Содержание RC4614

Отзывы:

Похожие инструкции для RC4614

Бренды по названию

Популярные бренды