Land Pride RC4614 Скачать руководство пользователя страница 25

Страница: 25 / 66

Section 1: Assembly & Set-up

Table of Contents

7/30/20

RC4614 & RCM4614 Rotary Cutters 331-937M

Remove Shipping Bar With Transport Locks Set

Figure 1-17

Remove Shipping Crossbar

Refer to Figure 1-17:

WARNING

To avoid serious injury or death:

•

Metal shipping bands are under tension. Always wear eye

protection when cutting bands. Keep head, body, and body

extremities away from the area where the band will recoil

into when cut.

•

Make sure transport lock is set before removing shipping

bar. Stay clear of wing while removing shipping bar. Once

shipping bar is removed, the wing will fall suddenly until

caught by transport lock.

1. Make sure cutter is parked on a level surface with

room for the wing to unfold.

2. Idle engine, place gear selector in park,

fully retract

wing folding cylinder (#9)

, shut tractor off, set park

brake, and remove switch key.

3. Verify transport lock bar (#2) is rotated down and

secured to cylinder pin (#1) with hairpin cotter (#6).

4. Cut and remove shipping bands securing wing

wheels.

5. Remove hex locknut (#4) and shipping bar (#10) from

hex cap screw (#3).

6. Reinstall hex locknut (#4) to hex cap screw (#3) and

tighten to the correct torque.

Remove cotter pin (#7), flat washer (#5), and

shipping bar (#10) from cylinder pin (#8).

Do not

remove cylinder pin (#8) or transport lock (#2).

8. Replace flat washer (#5) and cotter pin (#7). Bend

one or more legs of cotter pin to secure it in place.

35268

NOTE:

A come-along may be needed to pull the

wing in before shipping bar (#10) can be removed.

Transport Lock Removed & Secured for Field Work

Figure 1-18

Unfold Wing Deck

Refer to Figure 1-18:

DANGER

To avoid serious injury or death:
Keep everyone out of the area where the wing deck will unfold.

The wing deck can fall suddenly.

WARNING

To avoid serious injury or death:
Watch hydraulic hoses as the wing lowers to be sure they don’t

catch causing hoses to stretch and pull loose from the

hydraulic cylinders.

1. Make sure cutter is parked on a level surface with

room for the wing to unfold.

2. Idle engine, place gear selector in park, raise wing to

its most upright position, shut tractor engine off, set

park brake, and remove switch key.

3. Rotate transport lock bar (#3) up to storage

bracket (#2). Secure with existing hairpin (#1).

4. Start tractor and lower wing down until resting on the

ground.

5. Set tractor control lever for wing cylinders in float

position.

6. To purge hydraulic cylinders, refer to

“Purge

Hydraulic System”

on page 25.

39118

Содержание RC4614



































































Результаты поиска

Содержание RC4614

Отзывы:

Похожие инструкции для RC4614

Бренды по названию

Популярные бренды

Land Pride RC4614, Руководство оператора

Результаты поиска

Содержание RC4614

Отзывы:

Похожие инструкции для RC4614

Бренды по названию

Популярные бренды