background image

Important Safety Information

7/30/20

1

Important Safety Information

These are common practices that may or may not be applicable to the products described in 

this manual.

Tractor Shutdown & Storage

If engaged, disengage power 

take-off.

Park on solid, level ground and 

lower implement to ground or onto 

support blocks.

Put tractor in park or set park 

brake, turn off engine, and remove 

switch key to prevent unauthorized 

starting.

Relieve all hydraulic pressure to 

auxiliary hydraulic lines. 

Wait for all components to stop 

before leaving operator’s seat.

Use steps, grab-handles and 

skid-resistant surfaces when 

getting on and off the tractor.

Detach and store implement in an 

area where children normally do 

not play. Secure implement using 

blocks and supports.

OFF

REMOVE

Look For The Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a 

potential hazard to personal safety involved and extra 

safety precaution must be taken. When you see this 

symbol, be alert and carefully read the message that 

follows it. In addition to design and configuration of 

equipment, hazard control, and accident prevention are 

dependent upon the awareness, concern, prudence, and 

proper training of personnel involved in the operation, 

transport, maintenance, and storage of equipment.

Safety Precautions for 

Children

Tragedy can occur if the operator 

is not alert to the presence of 

children, Children generally are 

attracted to implements and their 

work.

Never assume children will remain 

where you last saw them.

Keep children out of the work area 

and under the watchful eye of a 

responsible adult.

Be alert and shut the implement 

and tractor down if children enter 

the work area.

Never carry children on the tractor 

or implement. There is not a safe 

place for them to ride. They may 

fall off and be run over or interfere 

with the control of the power 

machine.

Never allow children to operate the 

power machine, even under adult 

supervision.

Never allow children to play on the 

power machine or implement.

Use extra caution when backing 

up. Before the tractor starts to 

move, look down and behind to 

make sure the area is clear.

Safety at All Times

Careful operation is you best 

insurance against an accident. 
All operators, no matter how much 

experience they may have, should 

carefully read this manual and 

other related manuals before 

operating the power machine and 

this implement. 

Thoroughly read and understand 

the “Safety Label” section, read all 

instructions noted on them.

Do not operate the equipment 

while under the influence of drugs 

or alcohol as they impair the ability 

to safely and properly operate the 

equipment.

The operator should be familiar 

with all functions of the tractor and 

attached implement, and be able 

to handle emergencies quickly.

Make sure all guards and shields 

are in place and secured before 

operating implement.

Keep all bystanders away from 

equipment and work area. 

Start tractor from the driver’s seat 

with hydraulic controls in neutral.

Operate tractor and controls from 

the driver’s seat only.

Never dismount from a moving 

tractor or leave tractor unattended 

with engine running.

Do not allow anyone to stand 

between tractor and implement 

while backing up to implement.

Keep hands, feet, and clothing 

away from power-driven parts.

While transporting and operating 

equipment, watch out for objects 

overhead and along side such as 

fences, trees, buildings, wires, etc. 

Do not turn tractor so tight as to 

cause hitched implement to ride 

up on the tractor’s rear wheel.

Store implement in an area where 

children normally do not play. 

When needed, secure implement 

against falling with support blocks.

!

Be Aware of 

Signal Words

A signal word designates a degree or 

level of hazard seriousness. The 

signal words are:

Indicates a hazardous situation that, if 

not avoided, will result in death or 

serious injury. 

Indicates a hazardous situation that, if 

not avoided, could result in death or 

serious injury.

Indicates a hazardous situation that, if 

not avoided, may result in minor or 

moderate injury.

WARNING

CAUTION

!

!

DANGER

!

Содержание RC4614



































































Отзывы: