Land Pride RC4614 Скачать руководство пользователя страница 28

Страница: 28 / 66

Section 1: Assembly & Set-up

Table of Contents

7/30/20

RC4614 & RCM4614 Rotary Cutters 331-937M

Adjust Driveline Hanger

Figure 1-22

Driveline Hook-up to Tractor

DANGER

To avoid serious injury or death:
Do not use a power take-off adapter. The adapter will increase

strain on the tractor’s power take-off shaft causing possible

damage to shaft and driveline. It will also defeat the purpose

of the tractor’s power take-off shield.

Refer to Figure 1-22 on page 24:

1. Rotate driveline hanger (#1) down.
2. If needed, collapse driveline (#5) by pushing tractor

end of driveline against splitter gearbox.

3. Pull back on yoke locking collar (#10) and slide yoke

over tractor power take-off shaft.

4. Release locking collar (#10) and continue to push

outer yoke onto the power take-off shaft until locking

collar snaps in place.

5. Driveline (#5) should now be moved back and forth to

ensure both ends are secured.

6. If main driveline is constant velocity with overrunning

clutch, then attach safety chain on the inner shield to

the cutter and safety chain on the outer shield to the

tractor. Check safety chains to make sure they are

attached to the inner and outer driveline shields.

If attached to cutter hitch, remove park jack (#3) and

stored on the weight box. For detailed instructions,

refer to steps 10-11 on page 16.

39157

IMPORTANT:

The shields on the constant velocity

driveline with overrunning clutch must not rotate. To

stop rotation, attach safety chains on the inner and

outer driveline shields to the implement and tractor.

Hydraulic Lift Cylinder With Stroke Control Spacers

Figure 1-23

Adjust Driveline Hanger

Refer to Figure 1-23:

1. Move tractor control lever to extend hydraulic lift

cylinder (#5) until pressure against stroke control

spacers (#1, #2, #3, & #4) is removed.

2. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 15.

3. Remove all stroke control spacers (#1, #2, #3, & #4)

from center hydraulic lift cylinder (#5) by spreading

them apart at the break line.

4. Start tractor and lower cutter until front skids are

resting on the ground or on support blocks.

5. Shut tractor down properly before dismounting.
6. Replace stroke control spacers (#1, #2, #3, & #4) as

needed to support wheels at this position.

Refer to Figure 1-22:

With driveline attached to tractor, rotate driveline

hanger (#1) up as shown.

8. Loosen nuts securing carriage bolts (#4) and adjust

driveline hanger (#1) up/down until there is a small

gap between driveline (#5) and hanger (#1).

9. If driveline hanger (#1) is adjusted fully up and needs

to adjust higher, remove carriage bolts (#4) and

reattach hanger to the upper two square holes (#2)

with existing flat washers, lock washers, hex nuts,

and carriage bolts (#4). Continue to adjust hanger to

underside of driveline.

10. Draw nuts securing carriage bolts (#4) up snug and

rotate driveline hanger (#1) down. If hanger makes

contact with driveline (#5), readjust hanger down

until it misses the driveline.

11. Tighten nuts for carriage bolts (#4) to the correct

torque.

12. Rotate driveline hanger (#1) down.

33866

IMPORTANT:

Always rotate driveline hanger down

after hook-up to prevent driveline damage.

Содержание RC4614



































































Результаты поиска

Содержание RC4614

Отзывы:

Похожие инструкции для RC4614

Бренды по названию

Популярные бренды

Land Pride RC4614, Руководство оператора

Результаты поиска

Содержание RC4614

Отзывы:

Похожие инструкции для RC4614

Бренды по названию

Популярные бренды