Land Pride 7000 Series Скачать руководство пользователя страница 5

Страница: 5 / 38

Important Safety Information

Table of Contents

9/16/20

7000 Series 556-433M

Important Safety Information

Look for Safety Symbol

The SAFETY ALERT SYMBOL indicates there is a

potential hazard to personal safety involved and extra

safety precaution must be taken. When you see this

symbol, be alert and carefully read the message that

follows it. In addition to design and configuration of

equipment, hazard control and accident prevention are

dependent upon the awareness, concern, prudence and

proper training of personnel involved in the operation,

transport, maintenance and storage of equipment.

Be Aware of Signal Words

Signal words designate a degree or level of hazard

seriousness.
DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

This signal word is limited to the most extreme situations,

typically for machine components that, for functional

purposes, cannot be guarded.
WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury, and includes hazards that are exposed when

guards are removed. It may also be used to alert against

unsafe practices.
CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury. It may also be used to alert against unsafe

practices.

Prepare for Emergencies



Be prepared if a fire starts



Keep a first aid kit and fire extinguisher handy.



Keep emergency numbers for doctor, ambulance, hospital

and fire department near phone.

Be Familiar with Safety Decals



Read and understand “

Safety Decals

” on page 4,

thoroughly.



Read all instructions noted on the decals.



Keep decals clean. Replace damaged, faded and illegible

decals.

Содержание 7000 Series







































Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды

Land Pride 7000 Series, Руководство оператора

Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды