Land Pride 7000 Series Скачать руководство пользователя страница 7

Страница: 7 / 38

Important Safety Information

Table of Contents

9/16/20

7000 Series 556-433M

Check for Overhead Lines

The harrow is a one section tillage tool and does not

require more transport height than the tractor it is

attached to. Contacting overhead electrical lines can

introduce lethal voltage levels on drill and tractor frames.

A person touching almost any metal part can complete

the circuit to ground, resulting in serious injury or death.

At higher voltages, electrocution can occur without direct

line or body contact.



Avoid overhead lines during folding, unfolding, transport

and parking.

Shutdown and Storage



Lower drill, put tractor in park, turn off engine, and

remove the key.



Secure drill using blocks and supports provided.



Detach and store drill in an area where children normally

do not play.

Practice Safe Maintenance



Understand procedure before doing work. Use proper

tools and equipment. Refer to this manual for additional

information.



Work in a clean, dry area.



Lower the drill, put tractor in park, turn off engine, and

remove key before performing maintenance.



Make sure all system pressure is relieved.



Disconnect battery ground cable (

) before servicing or

adjusting electrical systems or before welding on drill.



Inspect all parts. Make sure parts are in good condition

and installed properly.



Remove buildup of grease, oil or debris.



Remove all tools and unused parts from drill before

operation.

Содержание 7000 Series







































Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды

Land Pride 7000 Series, Руководство оператора

Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды