Land Pride 7000 Series Скачать руководство пользователя страница 31

Страница: 31 / 38

Maintenance and Lubrication

Table of Contents

9/16/20

7000 Series 556-433M

End of Season

11. Clean machine as much as possible. Remove all dirt

from rust prone parts like disc blades and bolt

threads.

12. Check over the machine for damaged or worn parts.

Replace or rotate worn parts as needed--hinge bolts,

clevis pins, bearings, blades, etc.

13. Check all bolts for tightness. Tighten as needed.

14. Check and tighten or replace any hydraulic leaks.

15. Check hoses for any leaks.

16. The wheel bearings should be cleaned and repacked

annually or every 2500 acres.

17. Remove the gang bolt thread protector caps and

check gang nut torque (900 to 1100 ft-lbs). Clean out

any dirt on castle nut and threads. Use Anti-Seize on

the gang bolt threads before tightening castle nut.

18. Grease the Disk Harrow in all locations shown in the

lubricating section.

19. If stored outside, place a protective coating of grease

or "plow paint" on all earth working parts to prevent

rusting.

20. Place boards under the disk gangs and lower the

Disk Harrow to the ground retracting the lift cylin

ders. If disk is folded, remove transport locks before

lowering disk.

Beginning of Season

21. Hitch the tractor to the Disk Harrow and connect the

hydraulic hoses.

22. Check lift cylinders for leaks that could have caused

air to enter cylinders. If leaks are noticed repair cylin

ders and fully purge air from cylinders by unpinning

cylinder, block up and fully cycle cylinders back and

forth several times.

23. Slowly raise the machine a couple of times to its full

height and hold lever for 10 to 15 seconds to purge

air from lift cylinders.

24. If machine was not serviced and greased at end of

last season, perform steps 9 thru 14 from End of

Season section.

25. Make sure all moving parts move freely and do not

bind.

26. Take the time to read the operators manual and

refresh yourself with the safety information and oper

ating instructions.

27. It is the owner’s responsibility to see that all opera

tors of the Disk Harrow know the safety and operat

ing information found in this manual.

Содержание 7000 Series







































Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды

Land Pride 7000 Series, Руководство оператора

Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды