Land Pride 7000 Series Скачать руководство пользователя страница 25

Страница: 25 / 38

Transporting the No-Till Drill

Table of Contents

9/16/20

7000 Series 556-433M

Thread Protectors

Refer to Figure 11

5. Make sure thread protector bolts (1) are in place and

tight. Gang bolt thread damage may occur at hinge

point when gangs flex without protector caps. Lost

caps with no bolt may allow gang nut to become

loose.

Adjusting and Using Tractor Hydraulics

Depth Control

Refer to Figure 12

6. When you have machine level and set to the desired

working depth, set the depth stop (2) on the depth

stop tube (3). This is located at the front of the

machine. This will maintain a constant depth each

time after raising and lowering machine. One full turn

of the handle (4) will change the depth approximately



”. Turning the crank clockwise 1 turn is a



”

shallower working depth. Turn 2 turns counter

clockwise is



” deeper working depth.

Tires must remain on the ground at all times. Wheels off the

ground will induce high loads on level linkage and hitch,

causing premature wear and possible frame failure.

Tractor Detents

7. After the depth stop on the tractor is set, in order to

preserve the life of the cylinders, it is important to

properly set the detent on the tractor. The 7000

series disk harrow is equipped with re-phasing lift

cylinders. These cylinders have a re-phasing port at

the top of the cylinder (end stroke). If the tractor flow

rates and detents are not set properly, extreme oil

flow through these ports can destroy cylinder seals

causing internal leakage.

8. Tractors with timed detents (electric over hydraulic):

The flow on the tractor should be set so the disk will

raise from field position to full lift in approximately 3

to 5 seconds which is about 10 gpm. Not 10 on the

tractor indicator. More important is the detent. Once

the flow has been set, set the timed detent so that it



to 1 second longer than it takes to fully lift the

unit. If you set it less than this it will not properly

re-phase the cylinders. If you set it more than this,

you may be causing damage to the seals.

Figure 11

Thread Protectors

43415

Figure 12

Depth Control

TP-69486

Содержание 7000 Series







































Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды

Land Pride 7000 Series, Руководство оператора

Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды