Land Pride 7000 Series Скачать руководство пользователя страница 28

Страница: 28 / 38

Transporting the No-Till Drill

Table of Contents

7000 Series 556-433M

9/16/20

Rolling Harrow and Reel (Option)

Refer to Figure 16

15. The rolling harrow (1) is a versatile leveling

attachment and requires very little adjustment. The

reel down pressure may be adjusted by removing

the pin (2) and then either pushing the handle (4)

forward to increase the spring pressure or by pulling

the handle backwards to decrease the spring

pressure (3). When the desired amount of spring

pressure is set, re-insert the pin (3). Note: It is

recommended to run little or no down pressure in

wet or sticky field conditions.

16. If your machine is equipped with a hydraulic reel

attachment you will need to hook up the hydraulic

lines and then you well set the down pressure from

the cab of your tractor. There will not be a handle to

adjusted.

Refer to Figure 17

17. The bars on the reels are angled forward (5) and

should be installed as such on the machine. In some

conditions in which a firming of the soil is more

desirable than breaking up clods then these reels

can be mounted in reverse (6). This does however

increase the chance of causing damage to the bars

in rocky soil.

18.

Be sure reels are installed with twisted bars oriented

forward

(5)

as shown. Mounting in reverse

(6)

can

damage reel in rocky soil.

.eps

46%

Figure 16

Reel Adjustment

TP-69484

.eps

46%

Figure 17

Reel Direction

42284

Содержание 7000 Series







































Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды

Land Pride 7000 Series, Руководство оператора

Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды