Land Pride 3P806NT Скачать руководство пользователя страница 85

Страница: 85 / 92

Appendix C - Accessory Installation

Table of Contents

2019-01-23

3P806NT 313-520M

Appendix C - Accessory Installation

Carbide Disc Scraper Installation

Optional carbide disc scrapers are not factory installed.

See page 53 for ordering information. These instructions

describe installation of kit:

121

781A SPRING SCRAPER ASSEMBLY

Start with row 1 (left-most row unit):
39. Remove one or both disc blades to gain safe access

to the mount . Note the position of bushings and

spacers for correct re-assembly (page 34).

40. Remove the existing slotted scraper.

Refer to Figure 55

41. Select one:

802

079C HHCS 3/8

16X1 1/4 GR5

If Seed-Lok

is present, or also being mounted,

also select one:

804

013C WASHER LOCK SPRING 3/8 PLT

Place the lock washer

on the bolt

(because

the nut is not used).

42. Select one:

804

012C WASHER FLAT 3/8 SAE PLT

Place this flat washer on the bolt.

43. Select one:

If the blades were not completely pre-assembled,

select one each:

K7090 AIR DESIGN SCRAPER LH SIDE
K7091 AIR DESIGN SCRAPER RH SIDE
K7096 SPACER AND WASHER ASSEMBLY
K7093 AIR DESIGN SCRAPER 15LB SPRING

Nest one side (

) behind the other. Connect

the spring

between the sides, using the small top

holes. Insert the spacer

from the front, with the

narrow raised center to the rear (in the large blade

holes).

44. Insert the bolt through the scraper blades (

)

and spacer

45. If no Seed-Lok

is present, select one each:

804

013C WASHER LOCK SPRING 3/8 PLT

803

014C NUT HEX 3/8

16 PLT

Secure the scraper assembly to the scraper

mount using the lock washer

and nut

If a Seed-Lok

is present (not shown), secure the

scraper assembly to the Seed-Lok

, using a threaded

hole present in the Seed-Lok

. The hex nut is

unused.

46. Re-mount the removed disc blade.

Figure 55

Carbide Disc Scraper Installation

19000

Содержание 3P806NT





























































































Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды

Land Pride 3P806NT, Руководство оператора

Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды