Land Pride 3P806NT Скачать руководство пользователя страница 22

Страница: 22 / 92

Operating Instructions

Table of Contents

3P806NT 313-520M

2019-01-23

Operating Instructions

This section covers general operating procedures.

Experience, machine familiarity and the following

information will lead to efficient operation and good

working habits. Always operate farm machinery with

safety in mind.

Pre-Start Checklist

High Pressure Fluid Hazard:

Escaping fluid under pressure can have sufficient pressure to
penetrate the skin. Check all hydraulic lines and fittings before

applying pressure. Fluid escaping from a very small hole can
be almost invisible. Use paper or cardboard, not body parts,

and wear heavy gloves to check for suspected leaks. If injured,

seek immediate medical attention from a physician familiar
with this type of injury.

1. Carefully review “

Important Safety Information

”

starting on page 1.

2. Lubricate drill as indicated under “

Lubrication and

Scheduled Maintenance

” on page 48.

3. Check all tires for proper inflation. See “

Tire

Inflation Chart

” on page 58.

4. Check all bolts, pins and fasteners. Torque as shown

in “

Torque Values Chart

” on page 59.

5. Check drill for worn or damaged parts. Repair or

replace parts before going to the field.

6. Check hydraulic hoses, fittings and cylinders for

leaks. Repair or replace before going to the field.

7. Rotate the each ground drive wheel to see that the

drive system and meters are working properly and

free from foreign material.

8. Check that the caster pivots are unlocked.

Falling hazard:

Watch your step when walking on drill ladder and walkboard.

Falling from drill could cause severe injury or death.

WARNING:

Cancer and Reproductive Harm - www.P65Warnings.ca.gov

To prevent injury or death:

Read and understand Operator’s Manual before using.
Lower implement, stop tractor engine, set park brake and remove ignition

Do now allow riders.
Keep others away during operation.
Safely support and secure implement before repairs are made.

key before servicing, adjusting, repairing or unplugging.

CAUTION

818-719C

WARNING

To avoid serious injury or death:

Watch your step when climbing ladder or
walking on walkboard.

838-102C

Содержание 3P806NT





























































































Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды

Land Pride 3P806NT, Руководство оператора

Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды