Land Pride 3P806NT Скачать руководство пользователя страница 36

Страница: 36 / 92

Adjustments

Table of Contents

3P806NT 313-520M

2019-01-23

Coulter Depth (Individual Rows)

The running depth of all coulters is adjusted

simultaneously by changing the tool bar height. Adjusting

the height of a small number of coulters may be useful

for rows in tire tracks.
Adjust individual coulters as follows.
1. On level ground, lower the drill until coulters just

touch the ground.

2. Raise the drill by the extra amount you need to lower

the rows in tracks.

Refer to Figure 18

3. At each coulter to be adjusted, slightly loosen all six

bolts ( , ) at the mount.

4. Using a rubber mallet, tap the spring bar up or

down until the bottom edge of the coulter disc is at

ground level.

5. Tighten the two clamp bolts until both U-bolts are

firmly against the edge of the spring bar . It is

normal for there to be a small gap between the

clamps.

6. Tighten the four U-bolts .
7. Lower the drill and pull forward 30 feet (10m).
8. Check coulter blade to opener blade (furrow

centerline) alignment.

Drill Weight Adjustment

In heavy no-till conditions, or if it is otherwise necessary

to increase coulter spring force, extra frame weight is

probably required (or the higher forces will just lift the drill

off the ground, resulting in unreliable ground drive

operation).
Adding weight requires the optional weight kit and

user-provisioned standard “suitcase” tractor weights (kit

does not include weights). See page 57 for ordering and

page 83 for installation.
The kit includes two brackets. Each bracket accepts up

to five 100 pound (45 kg) weight. The following table

shows the additional force per row that the kit can

provide.

Note: Do not adjust the bar height of all coulters. Use the

tractor 3-point lift arms and front gauge wheel to

set group coulter height (page 16).

Figure 18

Frame-Mounted Coulter Height

10300

Figure 19

Adding Weights

28364

Weights

Additional Force per Row

Added

Pounds

Kilograms

32337C

Содержание 3P806NT





























































































Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды

Land Pride 3P806NT, Руководство оператора

Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды