Lamtec FMS Series Скачать руководство пользователя страница 40

Страница: 40 / 74

System Operation

Fault 121...125

The monitoring processor checks whether the present correction values lies within the range
set.

Check correction range
Otherwise A7

Fault 301, 302

Correction input is configured for 4

...

20 mA, but the instantaneous value is < 4 mA.

Wire is possibly broken or connection poles are transposed.
Check wiring
Check parameter 431, 432

Selector switch on LR1 on "Measure”

at output 0

...

20 mA but no 10 mA,

at output 4

...

20 mA but no 12 mA

Centre position potentiometer P4 on power unit LPE 1/S possibly set incorrectly

(see LR 1 operating instructions)
Turn potentiometer to 10 or 12 mA (on LPE 1/S)

A value other than200 or +/-100 is displayed.

The maximum correction range according to the standard software setting is 200 points.

Other range sizes are available for special cases.

50% is not displayed

Either 10 or 12 mA are not fed to the FMS

Measure current

Check wiring

Otherwise the same as F2 or F3

Jumpers are incorrectly inserted on the back of the front panel.

Check current

Fault 381, 382

The values of the correction input signals are compared between main and monitoring proces-
sor.

Change processor card

Message "Correction effect switched off, since over 97% for longer than 1 hour”.

TIP:
The correction signal is monitored in order to be able to detect an error function of the correc-
tion signal source (in O

regulation). If a correction signal >97% is present on the input for 1

hour a defect is assumed and the correction influence is disregarded.

Содержание FMS Series











































































Результаты поиска

Содержание FMS Series

Отзывы:

Похожие инструкции для FMS Series

Бренды по названию

Популярные бренды

Lamtec FMS Series, Быстрая справка для пользователя

Результаты поиска

Содержание FMS Series

Отзывы:

Похожие инструкции для FMS Series

Бренды по названию

Популярные бренды