Lambrecht Ser[LOG] Скачать руководство пользователя страница 47

Страница: 47 / 129

LAMBRECHT meteo GmbH

Ser[LOG] Manual

Page 47 of 129

The button

displays a PDF document assigned to the sensor, e. g. the corresponding

wiring diagram.

5.3.5.1

Configuration Global Radiation Sensors

If global radiation sensors are config-

ured, it is necessary to enter the indi-

vidual EMK for these sensors in the

"Settings Details" window. This value

represents the signal sensitivity and is

usually given in µV/(W/m²) in the doc-

umentation of the global radiation

sensors.

5.3.5.2

Configuration of a pair of vectorially linked wind sensors

If wind speed and wind direction are to be calculated vectorially to the mean value, the wind sensors

must be defined as wind pairs.

To do this, first create a wind speed sensor without a vector partner.

Then create a wind direction sensor and link

it to the previously created wind speed sen-

sor in the "Vector partner wind sensors" se-

lection box in the "Settings Details" window.

Now open the "Settings Details" window of

the channel with the wind speed sensor and

connect it to the corresponding wind direc-

tion sensor.

If no vector partner is selected in each case, the calculation of the mean value for the wind direction is

still vectorial, whereby a wind speed of constant 1 m/s is calculated. In this case, the mean value of the

wind speed is calculated scalar.

5.3.5.3

Configuration serial sensors

The configuration of the serial sensors takes place in 3 steps:

1. First of all, the Ser[LOG] must be informed about the interfaces to which the sensors are con-

nected, and which protocol is used by the sensors.

2. For sensors with SDI-12, Modbus RTU or Modbus TCP, the time interval at which the Ser[LOG]

should retrieve the data from the sensor must be set.

3. Afterwards, the transmitted parameters/measured values must be assigned to the internal

measurement channels.

5.3.5.3.1 Configuration of the serial interface for sensors

For the sensor assignment of the interfaces, please open the register selection "Interfaces" of the con-

figuration window.

Содержание Ser[LOG]


































































































































Результаты поиска

Содержание Ser[LOG]

Отзывы:

Похожие инструкции для Ser[LOG]

Бренды по названию

Популярные бренды

Lambrecht Ser[LOG], Руководство оператора

Результаты поиска

Содержание Ser[LOG]

Отзывы:

Похожие инструкции для Ser[LOG]

Бренды по названию

Популярные бренды