laguna CEF236230175, Руководство по установке и обслуживанию

Страница: 10 / 45

Fusion Tablesaw
10
 STORE IDLE POWER TOOLS OUT OF THE REACH OF CHILDREN AND DO NOT ALLOW PERSONS UNFAMILIAR WITH THE POWER TOOL OR THESE
INSTRUCTIONS TO OPERATE THE POWER TOOL.
Power tools are dangerous in the hands of untrained users.
 MAINTAIN POWER TOOLS AND ACCESSORIES. CHECK FOR MISALIGNMENT OR BINDING OF MOVING PARTS, BREAKAGE OF PARTS AND ANY OTHER
CONDITION THAT MAY AFFECT THE
power tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.

KEEP CUTTING TOOLS SHARP AND CLEAN.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

USE THE POWER TOOL, ACCESSORIES AND TOOL BITS ETC. IN ACCORDANCE WITH THESE INSTRUCTIONS, TAKING INTO ACCOUNT THE WORKING
CONDITIONS AND THE WORK TO BE PERFORMED.
Use of the power tool for operations different from those intended could result in a hazardous situation.
 KEEP HANDLES AND GRASPING SURFACES DRY, CLEAN AND FREE FROM OIL AND GREASE.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
 USE PROPER SPEED.
A machine will do a better and safer job when operated at the proper speed;
 USE THE CORRECT TOOL FOR THE JOB.
Know the limitations and capabilities of your new purchase. Do not try to “fit a square peg in a round hole.”
 SECURE THE WORK PIECE.
For all woodworking and metalworking applications, the workpiece should be secured correctly by the operator using appropriate clamps and vises. Always use a clamp
or vise when available — it is safer than using your hands.
 FEED DIRECTION.
If feed rate is applicable, then there is only one direction of feed rate for the tool. Do not force the workpiece in the wrong feed direction.
 NEVER LEAVE TOOL RUNNING UNATTENDED.
Do not leave the tool until it comes to a complete stop. When unattended, unplug the tool.
 MAINTAIN TOOLS WITH CARE
Keep cutting tools sharp and clean for better and safer performance
 Follow instruction for lubricating and changing accessories
Inspect tool cords periodically and if damaged have then repaired by an authorized service facility.
Inspect extension cords periodically and replace if damaged.
Keep hand dry, clean and free from oil and grease.
 ILLUMINATION
Adequate general or localized lighting shall be provided
 Dust Collection
During use the saw benches shall be connected to an external chip and dust extraction system
Guarding related warnings
 KEEP GUARDS IN PLACE. GUARDS MUST BE IN WORKING ORDER AND BE PROPERLY MOUNTED.
A guard that is loose, damaged, or is not functioning correctly must be repaired or replaced.
 ALWAYS USE SAW BLADE GUARD AND RIVING KNIFE FOR EVERY THROUGH–CUTTING OPERATION.
For through-cutting operations where the saw blade cuts completely through the thickness of the workpiece, the guard and other safety devices help reduce the risk of
injury.

MAKE SURE THE SAW BLADE IS NOT CONTACTING THE GUARD, RIVING KNIFE OR THE WORKPIECE BEFORE THE SWITCH IS TURNED ON.
Inadvertent contact of these items with the saw blade could cause a hazardous condition.

ADJUST THE RIVING KNIFE AS DESCRIBED IN THIS INSTRUCTION MANUAL.
Incorrect spacing, positioning and alignment can make the riving knife ineffective in reducing the likelihood of kickback .

FOR THE RIVING KNIFE TO WORK, IT MUST BE ENGAGED IN THE WORKPIECE.
The riving knife is ineffective when cutting workpieces that are too short to be engaged with the riving knife. Under these conditions a kickback cannot be prevented by
the riving knife.
 USE THE APPROPRIATE SAW BLADE FOR THE RIVING KNIFE.
For the riving knife to function properly, the saw blade diameter must match the appropriate riving knife and the body of the saw blade must be thinner than the
thickness of the riving knife and the cutting width of the saw blade must be wider than the thickness of the riving knife.