Laguna Tools Fusion 3, Руководство пользователя

Страница: 11 / 40

Fusion Tablesaw
© 10/2017, Laguna Tools, Inc.
9
General Safety
Electrical
DISCONNECT THE POWER FIRST. Always disconnect machine from power
supply BEFORE adjusting, changing tooling, or servicing machine.
USE A QUALIFIED ELECTRICIAN FOR ALL ELECTRICAL CONNECTIONS.
Failure to do so may result in damage to the tool and electrical shock to the
operator and bystanders.
POWER PLUGS. Your machine may not come with a power plug because of
the variance in power receptacles. Consult with a local electrician prior to
purchasing a power plug.
EXTENSION CORDS. Consult with or use a qualified electrician prior to sizing
extension cords for use with this machine. Repair any damaged extension
cords when discovered. The following table should only serve as a guideline
to choosing the appropriate extension cord.
A.W.G CORD SIZE
TOOLS
AMPERAGE
RATING
VOLTS CORD LENGTH IN FEET
120 25 50 100 150
240 50 100 200 -
3-6 18 ga. 16 ga. 16 ga. 14 ga.
6-8 18 ga. 16 ga. 14 ga. 12 ga.
8-10 16 ga. 14 ga. 12 ga. 12 ga.
10-12 14 ga. 14 ga. 12 ga. 10 ga.
12-16 14 ga. 12 ga. - -.
16-20 12 ga. 12 ga. - -
Note: The smaller the AWG gauge (ga.) size, the wider the cord.
Grounding
In the event of a malfunction, properly grounding the tool provides a path for
electric charge to dissipate in a safe manner.
DO NOT MODIFY THE PLUG. Do not remove any of the prongs attached to
the proper plug for the machine.
USE ONLY 3-WIRE EXTENSION CORDS. Some extension cords only have
two wires, which does not allow for grounding.
ALLWAYS USE GROUNDED CONNECTIONS. Connect to power sources
only in the following ways:
Rulings
warning:
Before connecting this tool to a power supply
(receptacle, outlet, etc.) make sure that the voltage supplied is the
same that is specified on the nameplate of the tool.
Also make sure that the power supply is equipped with the
appropriate breaker and plug according to your local electrical
code.
IF IN DOUBT, DO NOT PLUG IN THE MACHINE. Using this tool
with a voltage different than that stated on the nameplate can
damage the electrical components of this machine and any such
damage will not be covered by a warranty.
warning:
Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contains chemicals known
to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paint.
•
Crystalline silica from bricks, cement, and other masonry
products.
•
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals, work in
a well-ventilated area and work with approved safety equipment,
such as face or dust masks that are specifically designed to filter
out microscopic particles.
A notice about safety and Tool Use
The tools sold by Laguna Tools are safe when used properly, described by
The American National Safety Institute, the UL Standards of safe tool use,
and the IEC standards of safe tool use. Laguna Tools is in no way responsible
for injury or death that occurs while using this product. YOUR PERSONAL
SAFTEY IS 100% YOUR RESPONSIBILITY AND USING THIS PRODUCT
REQUIRES 100% OF YOUR ATTENTION.
If there is any concern related to the application you are intending to use this
tool for, DO NOT proceed until you have contacted Laguna Tools and have
been advised on the correct application of the product. You can easily contact
us by email at customerservice@lagunatools.com or by calling 1-800-234-
1976.
This manual is intended to thoroughly cover the setup up, maintenance, and
proper adjustments of your new purchase. Aside from the proceeding general
safety considerations, this manual DOES NOT cover woodworking or
metalworking techniques that are possible with this product and the
appropriate safety precautions necessary for safe practices. There are several
organizations with published safe practices, techniques, and proper operation
of this tool.
Power Tool Institute
www.powertoolinstitute.com
ANSI 01.1 Safety Requirements for Woodworking Machines
American National Standards Institute
www.ansi.org