Lagler Flip Скачать руководство пользователя страница 20

Страница: 20 / 64

FLIP

01.01.2019

English / Englisch

WARNING!

RISK OF DEATH from electrical shock:

The machine may never be used for wet processing operations
of any kind!

WORKING WITH THE FLIP

5.1 GENERAL APPLICATION TIPS

WARNING!

RISK OF DEATH from electrical shock:

The machine may never be used for wet processing operations
of any kind!

ATTENTION!

•

Bear in mind that the FLIP

operates at very high cutting

speeds! For this reason, there is a risk of burn marks for
finer grit grades!

•

Do not apply excessive pressure to the attachment while
sanding!

Excessive

pressure

- significantly worsen the sanding finish by causing deep

scratches or burn marks on the floor,

- could cause the motor to switch off from overheating!

The FLIP

is used for the dry sanding of edges, corners and stairs.

The attachment can be changed in a matter of seconds (

Sec-

tion 7.3.1, Removing the V-belt, step 1 to 6

and

Section

7.3.2, In-

stalling the V-belt, step 5 to 8

•

The FLIP

with

short

long attachment

is handled with rotary

clockwise

movements (fig. 12) during the sanding process!

•

The FLIP

with

corner attachment

is handled with

counterclockwise

movements (fig. 13) during the sanding

process! Otherwise deep sanding marks might be generated

which could be removed by a very time-consuming procedure

afterwards only!

•

Deep sanding marks due to the selection of a too coarse grit

grade can be prevented by starting the first sanding operation

with the finest grit grade possible.

Working with the FLIP

Fig. 11

Guide the FLIP

with both hands.

NOTE:

For more information free of charge, please

contact: within Germany

- Telephone: 0800 / 52 34 537

- Fax:

0800 / 48 66 353

within the USA

- Telephone: 800-848-6635

- Telephone: 0049 - 7135 - 98 90 - 0

- Fax:

0049 - 7135 - 98 90 - 98

- E-mail:

[email protected]

- Internet:

http://www.laegler.com

You will also find important and interesting

application tips in the LÄGLER

application

technique manual “Sanding of wooden

floors” (http://www.laegler.com)!

Fig. 12

FLIP

with

short

long

attachment:

Rotary

clockwise

movements!

Содержание Flip

































































Результаты поиска

Содержание Flip

Отзывы:

Lagler Flip, Руководство по эксплуатации, Страница: 20 / 64

Результаты поиска

Содержание Flip

Отзывы: