Labounty 513914 Скачать руководство пользователя страница 14

Страница: 14 / 98

Page 2

Section 2

About the Attachment

MOBILE DEMOLITION PROCESSORS

MDP models are currently available for base machines with operating weights from 20,000 - 70,000 lbs with

jaw openings of up to 36" (0.9m). Call to check availability of models outside of these ranges. Both rotating

and non-rotating models are available. Rotating models feature hydraulically powered 360º continuous rota-

tion. This option allows the jaws to be positioned to cut at virtually any angle. MDPs feature high-strength,

abrasion-resistant steel construction to assure long, uninterrupted service—even in the harshest conditions.

The main pivot shaft of every model is manufactured for long life and pivots on Stanley LaBounty’s specially

designed bearings. The jaws are designed to draw the materials in to the point where the proceesor force is

greatest, making them the most efficient cutting tool possible.

MDPs can crush concrete and cut a wide variety of materials including I-beams, H-beams, channel iron, steel

plate, pipe, round stock, wire, rebar and concrete. They are ideal for processing, demolition work, road and

bridge reconstruction, and jobs where torching is not feasible.

MODEL DESCRIPTION

FEATURES

• Patented quick change

jaw pivot allows for inter-

changeable jaws with mul-

tiple jaw options (Figures

2-2 and 2-3, page 3)

• Easily removable main

shaft

• 360º powered rotation

• Reversed cylinder

• Multiple machine mount

capability

• Patented, Swift-Lock

pin-on replaceable teeth

offer long wear and impact

resistance. One pin secures

each tooth segment—a

complete set of teeth can

be replaced in minutes

• Made with high-strength

steel for durability

• At-factory upgrading and

rebuilding services available
for extended life

FIGURE 2-1

Содержание 513914



































































































Результаты поиска

Содержание 513914

Отзывы:

Похожие инструкции для 513914

Бренды по названию

Популярные бренды

Labounty 513914, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 513914

Отзывы:

Похожие инструкции для 513914

Бренды по названию

Популярные бренды