Labounty 513914 Скачать руководство пользователя

Страница: 24 / 98

Page 4

Section 3

Installation

MOBILE DEMOLITION PROCESSORS

Figure 3-3

Figure 3-4

SECOND MEMBER ATTACHMENT MOUNTING PROCEDURE

Locate flat, hard ground for installation. Place the attachment on the ground with blocking.

Remove the excavator stick following manufacturer’s recommended procedure.

Take care to properly plug any hydraulic hoses when disconnected to prevent contamination from entering

the hydraulic system.

With the jaws of the attachment facing the excavator, bring the excavator into position, carefully lining up

the excavator boom tip with the boom pivot connection on the attachment mounting bracket (see Figure

3-3).

On a second member mount, it may be

necessary to block the rear of the attach-

ment in a position to allow boom pivot pin

installation.

NOTICE

Pin the excavator’s boom and attachment boom pivot together using the same pin that was used for pin-

ning on the stick.

Have all personnel stand clear and instruct the operator to slowly lift the attachment into a position where

there will be enough clearance to pin the excavator cylinder to the cylinder connection on the mounting

bracket (see Figure 3-4).

Extend the cylinder rod and position as necessary to connect to the cylinder connection of the attachment.

Install the pin provided with the mounting bracket. It may be necessary to use a lifting device (over-head

hoist, forklift, etc.) to position the cylinder correctly.

Never move or operate the attach-

ment without all collars and hardware

installed on the connecting pins.

Содержание 513914



































































































Результаты поиска

Содержание 513914

Отзывы:

Похожие инструкции для 513914

Бренды по названию

Популярные бренды

Labounty 513914, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 513914

Отзывы:

Похожие инструкции для 513914

Бренды по названию

Популярные бренды