Labounty 513914 Скачать руководство пользователя

Страница: 9 / 98

Introduction to Safety

Section 1

Page 3

MOBILE DEMOLITION PROCESSORS

If the attachment is not functioning properly, you

MUST

shut the machine down and follow lockout/

tag out procedures.

NEVER

operate equipment without the original

equipment safety guards in place. If the cab glass

is missing or damaged, check with your dealer or
manufacturer for proper replacement.

Ensure that the cab is equipped with the proper

safety guards for LaBounty applications. In addition,

it is required that the cab be equipped with an

approved Falling Object Protection Structure

(FOPS) when processing materials. The FOPS must

meet the requirements of SAE standard J1356. A

transparent shatter-resistant shield covering the

front of the cab is also required. Contact your base

machine equipment dealer or manufacturer for

more information on the availability of FOPS.

Lack

of proper FOPS may result in injury or death.

DO NOT

process or handle material with the

attachment over the operator’s cab.

DO NOT

attempt to shear brittle materials such

as axles and railroad rail. Brittle material breaks or

shatters instead of shearing. The material being

processed could become a projectile and cause

injury or death.

DO NOT

process any material in any

position that may propel it toward operator, other

workers, buildings or equipment.

DO NOT

close the attachment on a structure and

reverse the excavator in an attempt to pull down

material.

Clear all persons and equipment from the area of

operation and machine movement.

NEVER

move

loads over people or equipment. When viewing the

operation of the attachment, maintain a safe distance

of at least 75 feet (22.9 meters).

NEVER

approach power lines with any part of the

machine. Keep clear at a minimum of 15 feet (5

meters).

Avoid tipping. The attachment will alter the lift

capacities of the base machine.

DO NOT

overload

the excavator or serious injury could result. Lift

capacities will vary if the base machine is not on

level ground. Carry loads in recommended positions

for maximum stability. Use the recommended

excavator counterweight. Use short slings and lift

the load only as high as necessary.

DO NOT

allow riders on the machine.

NEVER

modify or mount the attachment to an

excavator other then which it was originally designed

for without consulting LaBounty. Rotation component

failure may result, causing the attachment to fall to the

ground.

SAFETY SUMMARY

Содержание 513914



































































































Результаты поиска

Содержание 513914

Отзывы:

Похожие инструкции для 513914

Бренды по названию

Популярные бренды

Labounty 513914, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 513914

Отзывы:

Похожие инструкции для 513914

Бренды по названию

Популярные бренды