Labounty 513914 Скачать руководство пользователя страница 38

Страница: 38 / 98

Page 2

Section 5

Maintenance

MOBILE DEMOLITION PROCESSORS

• ALWAYS wear proper safety equipment when

maintaining the attachment including safety glasses

with side shields, hard hat, steel toe shoes, gloves,

and hearing protection.

• Be sure you understand a service procedure

before working on the machine. DO NOT ATTEMPT

REPAIRS YOU DO NOT UNDERSTAND. ASK FOR
HELP BEFORE STARTING IF YOU ARE UNSURE.

GENERAL RULES FOR

MAINTENANCE

1. Read the maintenance procedures in this manual.

Be sure all maintenance personnel read and

understand all maintenance procedures before

working on the equipment.

2. Use factory approved parts. Use of parts

that are not factory approved by cause damage

or unnecessary downtime and may void the

attachment warranty.

3. Lubricate daily – follow the lubrications schedule

as outlined in this manual.

4. Use the included Inspection Checklists during

inspection to make sure all maintenance is
complete

5. In extremely cold temperatures work the

attachment on lighter materials first before working

up to heavier materials. This allows the attachment

and jaws to warm up and makes them less

susceptible to damage.

6. DO NOT weld on the excavator boom or stick

without first consulting your dealer.

MAINTENANCE SAFETY

PROCEDURES

Before attempting any maintenance procedure, read

the entire Safety Manual carefully. If any question

arises regarding a safety or maintenance procedure,

contact your LaBounty dealer. For the nearest

LaBounty dealer, see the Contact Information at the

front of this manual.

•Inspect the attachment daily. DO NOT operate a

poorly maintained or damaged attachment or major

structural damage could result.

• ALWAYS lower the boom to the ground before

leaving the cab. If it is necessary to work on an

attachment off the ground, securely support the

machine and attachment. DO NOT support the

machine on cinder blocks, hollow tiles, or props that

may crumble under continuous load. DO NOT rely

on the cylinder to hold the attachment in the air. If a

control is moved or hydraulic pressure is otherwise

released, the attachment will drop. DO NOT work

under a machine that is supported solely by a jack.

• DO NOT attempt to alter or change the physical,

mechanical or hydraulic operation of the attachment

during the warranty period without first consulting

Stanley LaBounty as this could invalidate the

Manufacturer’s Warranty.

• NEVER operate the machine if an unsafe condition

exists. Attach a “DO NOT OPERATE” tag to the

machine.

• If more than one person is working on a machine,

each must be familiar with the controls and aware

of what the others are doing. Before working on a

machine, BE SURE TO TAG THE CONTROLS SO NO

ONE ELSE WILL START IT.

• ALWAYS use two people when making checks

with the engine running – the operator at the

controls must be able to see the person doing the

checking.

• Keep hands away from moving parts. NEVER

lubricate or work on a machine while it is moving.

During maintenance of the attachment,

it is imperative that the excavator is turned OFF

to prevent injury.

Содержание 513914



































































































Результаты поиска

Содержание 513914

Отзывы:

Labounty 513914, Руководство по безопасности, эксплуатации и техническому обслуживанию, Страница: 38 / 98

Результаты поиска

Содержание 513914

Отзывы: