Labounty 513914 Скачать руководство пользователя

Страница: 34 / 98

Page 4 Section 4

Operation

MOBILE DEMOLITION PROCESSORS

THIRD MEMBER

INSTALLATION

(attachment replaces bucket)

A. BUCKET DUMP =

ATTACHMENT OUT

B. BUCKET CURL =

ATTACHMENT IN

Determine the control for each movement of the

processor before attempting to operate.

ATTACHMENT CONTROLS

The Stanley LaBounty Mobile Demolition Processor replaces the bucket of an excavator and operates

with the same controls—no additional hydraulics are required. The bucket dump control opens the

processor and the bucket curl control closes the processor; thus there are four movements of the

MDP plus rotation. The attachment controls will vary depending on the base machine on which it is

mounted and whether it is mounted as a second or third member. The MDP jaw and rotation systems

are customized to each machine. Review these functions with your authorized dealer or installation

technician before operating the attachment.

FIGURE 4-1

Содержание 513914



































































































Результаты поиска

Содержание 513914

Отзывы:

Похожие инструкции для 513914

Бренды по названию

Популярные бренды

Labounty 513914, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 513914

Отзывы:

Похожие инструкции для 513914

Бренды по названию

Популярные бренды