manualshive.com logo in svg

Labcyte Echo 520, Руководство пользователя, Страница: 62 / 200

Поделиться
Скачать
Labcyte Echo 520 Скачать руководство пользователя страница 62

3-4

Echo Liquid Handler User Manual

3.1.2 Back panel

Figure 3.3  Echo liquid handler back panel

AC power and fuse compartment: 

The AC power and fuse 

compartment (also called the power input module) contains the main Echo 
liquid handler power on/off switch, AC power outlet, and fuse 
compartment. For more information, see 

“AC power and fuse 

compartment” on page 3-14

.

Coupling fluid bottle and caddy: 

The 1000 mL coupling fluid bottle 

provides the coupling fluid (distilled water) that is pumped through the 
acoustic transducer to maintain constant temperature and transfer acoustic 
energy to the well. The coupling fluid bottle caddy contains a sensor that 
monitors the fluid level and issues a warning when the fluid level is less 
than 250 mL. For more information, see 

“Coupling fluid bottle” on 

page 3-15

.

Status light indicators, LCD 

screen

, and Emergency Off (EMO):  

Same 

as the components on the front panel. Remote EMO cable enables the 
customer to set up a remote EMO button more accessible to the operator. 

Data connection: 

RJ-45 Ethernet network port connects the Echo liquid 

handler to a PC or to a network. For more information, see 

“Data 

connection” on page 3-14

.

Tubing and hose connections:  

the Echo liquid handler uses tubing and 

hoses to connect to the chiller, house air, surge tank, and vacuum pump. 

Waste water bottle

 (not shown, on older Echo systems only)

:  

The 500 

mL waste water bottle collects overflow from the catch basin. 

Status lights
LCD 

screen

Emergency Off 
(EMO) switch

AC power and fuse

compartment

Tubing and hose 
connections

Data connection

Coupling fluid bottle 
and caddy

Remote Emergency Off  
cable

Содержание Echo 520









































































































































































































Отзывы:

Нет отзывов