manualshive.com logo in svg

Labcyte Echo 520, Руководство пользователя, Страница: 61 / 200

Поделиться
Скачать
Labcyte Echo 520 Скачать руководство пользователя страница 61

System Description

3-3

Source plate insert: 

The plate insert fits between the source plate and 

plate gripper to ensure that the source plate is properly positioned. For 
more information and table of insert types, see 

“Source plate insert” on 

page 3-6

.

Figure 3.2  Plate inserts

Status indicator lights: 

There are three status indicator lights on the front 

of the Echo liquid handler: 

Power 

(green): The Echo liquid handler is on and ready.

Warning

 (yellow): A component is out of position or a parameter is 

out of range and requires attention.

Fault

 (red): A problem has occurred that stops the current task and 

requires immediate attention. 

These status indicator lights are also provided on the back panel. For more 
information, see 

“Status indicator lights” on page 3-9

.

LCD screen:  

The LCD screen on the front of the Echo liquid handler 

reports what the Echo liquid handler is doing or what operator action is 
required. This display is also provided on the back panel. For more 
information, see 

“LCD screen” on page 3-11

.

Emergency off: 

The EMO (Emergency Motion Off) switch shuts down all 

mechanical Echo liquid handler activity. This switch is also available on the 
rear panel.

Upper and lower anti-static bars:  

The upper and lower anti-static bars 

remove any electrostatic charge from the source and destination 
microplates. Electrostatic charge can affect the travel of the droplet. For 
more information, see 

“Anti-static bars” on page 3-12

.

Barcode scanner option:  

An Echo liquid handler can be purchased with 

one or more barcode scanners that will read and report barcoded 
microplates. For more information, see 

“Barcode scanner” on page 3-12

.

Содержание Echo 520









































































































































































































Отзывы:

Нет отзывов