Labcyte Echo 520 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 200

Labcyte Echo 520 Скачать руководство пользователя страница 50

2-6

Echo Liquid Handler User Manual

2.3

Software installation

Labcyte installs the Echo software onto the client PC that is connected to
the Echo liquid handler. If you need to install the software onto additional
computers, such as network PCs, use the instructions provided in this
section.

See “Multi-client considerations” on page 1-23

for advantages and

disadvantages of connecting more than one workstation.

Note:

If you are connecting the Echo liquid handler to a LAN via a

hub, switch, or router, use a standard ethernet cable. If you are
connecting the Echo liquid handler directly to a workstation, use the
included “cross-over” Ethernet cable.

1

During installation the Echo software will provide the following
installation types:



Client (Only)

: Installs the Echo software onto the client PC that is

connected to the Echo liquid handler (normal mode). The software
allows the operator to communicate with, control, and monitor an
Echo liquid handler through easy-to-use software screens (Graphical
User Interface). This option requires a host name or IP address of the
Echo server.



Client and Server

:



Normal Mode

installs the Echo client software onto the client PC

and the Echo server software onto the Echo controller. This
software is installed by Labcyte field engineers.



Stub

Mode

creates a virtual Echo instrument onto the client PC

that developers can use to develop and test custom software.

Note:

Use this installation type only if you are writing your own

programs that will call the Echo ActiveX programming interface. Call
Labcyte Service and Support if you have any questions regarding this
installation type.

1 Ethernet cable that switches, or crosses over, receive and transmit wire pairs that enable

two devices to communicate with each other.

«
...
48
49
50
51
52
...
»

Содержание Echo 520









































































































































































































Отзывы:

Нет отзывов