manualshive.com logo in svg

Labcyte Echo 520, Руководство пользователя, Страница: 170 / 200

Поделиться
Скачать
Labcyte Echo 520 Скачать руководство пользователя страница 170

6-10

Echo Liquid Handler User Manual

6.2.3 Clean and refill the coupling fluid bottle

Clean

 and 

refill

 the fluid coupling bottle when one of the following 

occurs:

Fluid appears cloudy.

Two weeks have passed since the last coupling fluid refill.

Fluid transfer accuracy or precision has been affected by coupling 
fluid contamination.

Note:  

During periods of heavy duty cycle use, refilling the coupling 

fluid bottle will be necessary more frequently than once every two 
weeks. It is acceptable to skip the complete fluidic circuit purge as long 
as it is performed at least every second week.

The following procedures are needed to clean and refill the coupling fluid 
bottle. 

1.

Empty the coupling fluid bottle

2.

Purge the fluid circuit

3.

Clean and refill the coupling fluid bottle

4.

Cycle fluid through the Echo system

This section describes each task in detail.

Tools and materials needed

4 liters of 

distilled

 water. The Echo fluidic system holds about 

1100 mL of fluid (approximately 225 mL in the fluidic circuit and 
875 mL in the coupling fluid bottle). Emptying, purging, and filling 
the system will be performed several times.

Caution:  

Do not use de-ionized water, as it may corrode the fluidics 

system.

An empty, clean 1000 mL coupling fluid bottle (square bottle catalog 
number ECHO-AL15-S; round bottle catalog number ECHO-AL-15-R)

50 

μ

L of algaecide (Labcyte catalog number ECHO-AL04)

Gloves for protection when handling the algaecide

Paper towels or shop cloths to deal with any unexpected fluid leaks

Screwdriver for removing the fuse cover

The fluidic system will be emptied, purged, and refilled several times, 
therefore take note of the following caution:

Caution:  

When working with the Echo coupling fluid system and 

turning its coupling fluid pump on and off, make sure that the 
vacuum line is connected and working 

before

 turning the coupling 

fluid pump back on. If the vacuum line is disconnected or the vacuum 

Содержание Echo 520









































































































































































































Отзывы:

Нет отзывов