Labconco Protector Echo Скачать руководство пользователя страница 110

Страница: 110 / 112

110

Appendix F: Approved Chemicals

List of approved chemicals for GreenFumeHood

Technology (GFHT) with proprietary

Neutrodine

Filtration.

More information on the approved chemical long list can be found online through Erlab.
Get to the pdf on a computer by clicking

here

. If the embedded link did not work, follow

these steps:

1. Go to

Erlab.com

2. Hover your mouse on the

[Resources]

tab

3. Now find a section called LIBRARY
4. Click

[Chemical Listing GFH]

under the LIBRARY

section.

The Short List of Chemicals Not Recommended

Gaseous chemicals

In normal temperature and pressure conditions with very low boiling point (25°C, 1
Atmosphere). The following are examples:



Hydrogen (H

)



Ethane



Carbon dioxide



Propyne



Helium & noble gases



Ethylene oxide



Nitrogen monoxide



Acetylene



Methane



Carbon monoxide



Propylene

Organophosphorus compounds:

Because of their very high toxicity (compounds that can be used as Chemical
weapons).

Mercury:

In spite of the fact that this product is very well retained by Neutrodine, it remains
extremely toxic (TLV = 0,05 ppm) and very hard to detect.

Hydrogen Cyanide:

Immediately lethal

This edition of the GreenFumeHood

Chemical Guide 2019 has been developed by

Erlab

R&D laboratory, worldwide leader in filtration technologies for filtered hoods.

Содержание Protector Echo

















































































































Результаты поиска

Содержание Protector Echo

Отзывы:

Похожие инструкции для Protector Echo

Бренды по названию

Популярные бренды

Labconco Protector Echo, Руководство пользователя

Результаты поиска

Содержание Protector Echo

Отзывы:

Похожие инструкции для Protector Echo

Бренды по названию

Популярные бренды