background image

 

    

WARNING

 

This water heater needs fresh air for safe operation and must be installed so there are provisions for adequate 
combustion and ventilation air.  Insufficient air supply will cause a recirculation of combustion products resulting in 
contamination that may be hazardous to life.  This will result in carboning or sooting of the combustion chamber, 
burners, and flue tubes and creates a risk of asphyxiation.

 

This water heater requires its own separate venting system.  DO NOT connect the exhaust vent into an existing vent 
pipe or chimney.

 

Water heater materials of construction, products of combustion and the fuel contain carbon monoxide, nitrogen 
oxides, aldehydes and/or other toxic or harmful substances which can cause death or serious injury and which are 
known to the state of California to cause cancer, birth defects and other reproductive harm.  Always use proper 
safety clothing, respirators and equipment when servicing or working nearby this water heater.

 

Flammable items, pressurized containers or any other potential fire hazardous articles must never be placed on or 
adjacent to the water heater.  Open containers of flammable material should not be stored or used in the same room 
with this water heater.

 

Insulation blankets are not required for this water heater.  This water heater meets or exceeds the ASHRAE/IES 
90.1b (latest edition) standards with respect to insulation and standby loss requirements.

 

Hydrogen gas can be produced in an operating water heater that has not had water drawn from the tank for a long 
period of time (generally two weeks or more).  Hydrogen gas is extremely flammable.  To prevent the possibility of 
injury under these conditions, we recommend the hot water faucet to be open for several minutes at the kitchen sink 
before you use any electrical appliance, which is connect to the hot water system.  If hydrogen is present, there will 
be unusual sounds such as air escaping through the pipes as hot water begins to flow.  Do not smoke or have open 
flame near the faucet at the time it is open.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

                                                 

WARNING 

 
Liquefied petroleum gases/propane gas is heavier than air and will remain at floor level if there is a leak.
Basements, crawl spaces, closets and areas below ground level will serve as pockets for accumulation of leaking
gas.  Before lighting, smell all around the appliance area for gas.  Be sure to smell next to the floor. 
 
IF YOU SMELL GAS: 

• 

DO NOT try to light any appliance. 

• 

DO NOT touch any electric switch; do not use any telephone in your building. 

• 

Immediately call your gas supplier from a telephone in another building.  Follow the gas supplier’s
instructions. 

• 

If you cannot reach your gas supplier, call the fire department. 

DO NOT OPERATE THE APPLIANCE UNTIL THE LEAKAGE IS CORRECTED! 

 
 
 
 
 
 
 
 
 
 

 

4

Содержание U.H.E

















































Отзывы: