background image

EN

6

About this manual

This operating guide is an integral and 
essential part of the product and must be 
supplied to users. Users  are asked to read 
the enclosed warnings and cautions
carefully, as they provide valuable 
information concerning safety during 
installation, operation, and maintenance.
This manual must be kept in a safe place 
and be available for consultation to new 
and experienced users alike.

Remove machine from packaging

1)

Ensure product’s integrity by inspecting

the packaging, making sure it presents no 
signs of damage which might have affected 
the enclosed machine.

2)

Check the machine’s integrity after

having carefully removed the packaging.
Packaging (boxes, plastic bags, foam parts 
and whatever else) must not be left within 
easy reach of children, due to the potential 
danger it represents, nor be discarded in 
the environment.

Safety instructions

1)

Check to see that data on the rating

plate corresponds to those of the main 
electrical supply to which the machine will 
be attached.

This equipment must be installed to 
comply with applicable federal, state or 
local plumbing codes.

2)

The installation must be performed

according to local electrical and plumbing 
codes and regulations. The installation 
also must comply to the manufacturer’s
instructions, and must be performed by 

qualified and authorized personnel.

3)

Incorrect installation may cause injury/

damages to people, animals or objects, for 
which the manufacturer shall not be held 
responsible.

4)

Safe electrical operation of this device

will be achieved only when the connection 
to the power outlet has been completed 
correctly and in observance of all local, 
national, and international electrical codes 
and safety regulations, and particularly by 
grounding the unit. Make sure grounding 
has been done properly as it represents a 
fundamental safety requirement. Ensure 

qualified personnel check such connection.

5)

Furthermore, you must ensure that

the capacity of the available electrical 
system is suitable for the maximum power 
consumption indicated on the espresso 
machine.

6)

We do not recommend using adapters,

multiple plugs and/or extension cords. 
If you cannot avoid using them, make 
sure that they are exclusively of the kind 
which conforms to local, national, and 
international electrical codes and safety 
regulations, being careful not to exceed 
the power and current ratings indicated on 
such adapters and extension cords.

7)

This device must be used exclusively

for the functions it has been designed 
and built for. Any other application is 
inappropriate and dangerous.
The manufacturer shall not be held 
responsible for any damages caused by 
improper and/or irrational use.

8)

Using any electrical device requires that

certain fundamental rules be observed. In 
particular:
-  do not touch the device with wet or moist 

hands and feet

-  do not use the device while not wearing 

shoes

- do not use extension cords in bath or 

shower rooms

-  do not unplug the device from the power 

outlet by pulling on the power supply 
cable

-  do not expose the device to atmospheric 

agents

Содержание linea mini





























Отзывы: