KYMCO Xciting 250i Скачать руководство пользователя страница 21

Страница: 21 / 92

Tachometer: Indicates the engine speed in revolutions per

minute (RPM)

Left turn signal indicator

Speedometer: Indicates road speed in miles-per-hour

(MPH). The meter face also indicates road speed in kilo-

meters-per-hour (KPH)

Right turn signal indicator

Fuel level gauge

Fuel refill indicator “

”: This indicator lights when the

fuel tank is near empty to alert the rider to refill the fuel

tank as soon as possible.

Oil service indicator reset button: The oil service indicator

light can be reset by pressing the button. Do not press this

button until the oil has been serviced so it can notify you

when the next oil service is required.

Seat unlock indicator “MET-IN”: If this indicator is lit, it means

the seat is not locked in the closed position.

Side stand down indicator: This indicator will be lit if the

side stand is in the down position.

High beam indicator

CONTROLS & FEATURES

Cell phone socket indicator: Lights when the cell phone

recharging socket is being used

Coolant temperature gauge: Indicates engine coolant tem-

perature when the ignition switch is “ON”

Minute adjust button: Push this button to adjust the min-

utes on the clock display

Odometer/Tripmeter: Press the

button to toggle be-

tween the overall and trip mileage, or to reset the tripmeter

Clock

Hour adjust button: Push this button to adjust the hours on

the clock display

Oil service indicator: Lights when the scooter has reached

the oil service interval mileage. The indicator also lights

when the ignition is turned “ON” but should go out once

the engine is running.

CELP indication (250i/Ri, 300i/Ri & 500i/Ri models): If flash-

ing, it indicates that a fault has been detected in the

scooter’s EFI or electrical system. Requires immediate

inspection by a KYMCO dealer.

NOTE: The CELP indicator lights momentarily when

the scooter is turned “ON”, before the engine is run-

ning. It will also light if the engine is revved past its

upper RPM limit. The scooter’s ignition will begin to

limit engine speed to reduce the risk of potential en-

gine damage. The indicator will go out once the en-

gine speed has returned to the normal range.

Parking brake indicator (500i / 500Ri only): Indicates that

the parking brake is engaged.

Do not ride the scooter with the side stand down as

it could result in an accident.

Multifunction Meter - Xciting 300i & 500i

continued:

Содержание Xciting 250i





























































































Результаты поиска

Содержание Xciting 250i

Отзывы:

KYMCO Xciting 250i, Руководство пользователя, Страница: 21 / 92

Результаты поиска

Содержание Xciting 250i

Отзывы: