KYMCO MXU 500 Скачать руководство пользователя

Страница: 94 / 664

LOADING AND ACCESSORIES

Use extra caution when riding the machine with
additional loads, such as accessories or cargo.

The machine's handling may be adversely
affected. Reduce your speed when adding
additional loads.

MAXIMUM LOADING LIMIT:

FRONT CARGO RACK:

kg (100 lbs)

REAR CARGO RACK: 85 kg (187 lbs)

MAXIMUM TOWING CAPACITY:

TONGUE WEIGHT:

454 kg (1000 lbs)

16 kg (35 lbs)

Loading and operational guidelines

Carrying cargo will affect how your ATV handles
and greatly reduce its ability in accelerating,
braking and making turns and other maneuvers.

Be sure to observe the weight limits and follow
these guidelines:

1. Do not tow another vehicle.

2. Make sure all cargo is secured before riding.

3. Allow extra room for starting, stopping and

turning whenever you carry cargo or pull a

trailer.

4. Avoid riding on steep slopes when carrying

cargo or pulling a trailer.

5. Never cross a slope when towing a trailer.

Содержание MXU 500

























































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MXU 500

Отзывы:

Похожие инструкции для MXU 500

Бренды по названию

Популярные бренды

KYMCO MXU 500, Руководство пользователя

Результаты поиска

Содержание MXU 500

Отзывы:

Похожие инструкции для MXU 500

Бренды по названию

Популярные бренды