manualshive.com logo in svg

KYMCO MXU 500, Руководство пользователя

Поделиться
Скачать
KYMCO MXU 500 Скачать руководство пользователя страница 362

9. CYLINDER/PISTON

 

9-2

MXU 500

SERVICE INFORMATION

GENERAL INSTRUCTIONS

x

The cylinder and piston can be serviced with the engine installed in the frame.

x

When installing the cylinder, use a new cylinder gasket and make sure that the dowel pins are
correctly installed.

x

After disassembly, clean the removed parts and dry them with compressed air before inspection.

SPECIFICATIONS                                                                                                     

Unit: mm (in)

Item

Standard

Service Limit

I.D.

92.005 (3.6802)

阡

92.015 (3.6806)

92.1 (3.684)

Warpage

0.01 (0.0004)

0.05 (0.002)

Cylindricity

0.01 (0.0004)

0.1 (0.004)

True roundness

0.01 (0.0004)

0.1 (0.004)

Ring-to-groove

top

0.03 (0.0012)

阡

0.065 (0.0026)

0.08 (0.003)

clearance

Second

0.015 (0.0006)

阡

0.05 (0.002)

0.065 (0.0026)

top

0.15 (0.006)

阡

0.3 (0.012)

0.5 (0.02)

  Piston,

Ring end gap

Second

0.03 (0.012)

阡

0.45 (0.018)

0.65 (0.026)

  piston ring

Oil side rail

0.2 (0.008)

阡

0.7 (0.028)

1 (0.04)

Piston O.D.

91.96 (3.6784)

阡

91.98 (3.6793)

91.9 (3.676)

Piston O.D. measuring position

10 mm from bottom of skirt

－

.

Piston-to-cylinder clearance

0.01 (0.0004)

阡

0.045 (0.0018)

0.1 (0.004)

Piston pin hole I.D.

22.002 (0.8801)

阡

22.008 (0.8803)

22.04 (0.8816)

Piston pin O.D

21.994 (0.8798)

阡

22 (0.88)

21.96 (0.8784)

Piston-to-piston pin clearance

0.002 (0.0001)

阡

0.014 (0.0006)

0.02 (0.001)

Connecting rod small end I.D. bore

22.016 (0.8806)

阡

22.034 (0.8814)

22.06 (0.8824)

TORQUE VALUES

Cylinder bolt

1 kgf-m (10 N-m, 7.2 lbf-ft)

TROUBLESHOOTING

x

When hard starting or poor performance at low speed occurs, check the crankcase breather for
white smoke. If white smoke is found, it means that the piston rings are worn, stuck or broken.

Compression too low or uneven
compression

Excessive smoke from exhaust muffler

x

Worn or damaged cylinder and piston rings

x

 Worn or damaged piston rings

x

Worn, stuck or broken piston rings

x

 Worn or damaged cylinder and piston

Compression too high

Abnormal noisy piston

x

Excessive carbon build-up in combustion

x

 Worn cylinder, piston and piston rings

chamber or on piston head

x

 Worn piston pin hole and piston pin

x

 Incorrectly installed piston

Cylinder

Содержание MXU 500

























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды