manualshive.com logo in svg

KYMCO MXU 500, Руководство пользователя

Поделиться
Скачать
KYMCO MXU 500 Скачать руководство пользователя страница 250

3

. INSPECTION/ADJUSTMENT

 

3-24

      MXU 500

TOE-IN ADJUSTMENT

Place the machine on a level place.
Measure the toe-in
Adjust if out of specification.
Toe-in measurement steps:
Mark both front tire tread centers.
Raise the front end of the machine so that
there is no weight on the front tires.
Fix the handlebar straight ahead.
Measure the width A between the marks.
Rotate the front tires 180 degrees until the
marks come exactly opposite.
Measure the width B between the marks.
Calculate the toe-in using the formula given
below.
Toe-in = B

－

A

Toe-in: 0

阡

15 mm (0

阡

0.6 in)

If the toe-in is incorrect, adjust the toe-in.

Adjust the toe-in step:

   

Mark both tie-rods ends.

    This reference point will be needed during
  adjustment.
    Loosen the lock nuts (tie-rod end) of both
  tie-rods
    The same number of turns should be given
    to both tie-rods right and left until the
    specified toe-in is obtained, so that the
    lengths of the rods will be kept the same.

Tighten the rod end lock nuts of both tie-
rods

Torque: 

3.5 kgf-m (35 N-m, 25.2 lbf-ft)

x

Be sure that both tie-rod are turned the
same amount. If not, the machine will
drift tight or left even though the
handlebar is positioned straight which
may lead to mishandling and accident.

x

After setting the toe-in to specification,
run the machine slowly for some
distance with hands placed lightly on
the handlebar and check that the
handlebar responds correctly. If not,
turn either the right or left tie-rod
within the toe-in specification.

＊

Tie-rod

Tie-rod End Nuts

A

B

Содержание MXU 500

























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды