KYMCO MXU 500 Скачать руководство пользователя

Страница: 332 / 664

8. CYLINDER HEAD/VALVES

8-2

MXU 500

SERVICE INFORMATION

GENERAL INSTRUCTIONS

The cylinder head can be serviced with the engine installed in the frame. Coolant in the radiator

and water jacket must be drained first.

When assembling, apply molybdenum disulfide grease or engine oil to the valve guide movable

parts and valve arm sliding surfaces for initial lubrication.

The valve rocker arms are lubricated by engine oil through the cylinder head engine oil passages.

Clean and unclog the oil passages before assembling the cylinder head.

After disassembly, clean the removed parts and dry them with compressed air before inspection.

After removal, mark and arrange the removed parts in order. When assembling, install them in

the reverse order of removal.

SPECIFICATIONS

Unit: mm (in)

Item

Standard

Service Limit

0.1 mm (0.004 in)

Valve clearance (cold)

0.1 mm (0.004 in)

Cylinder head compression pressure 15 kg/cm

(1500 kPa, 213 psi)

Cylinder head warpage

0.05 (0.002)

Camshaft runout

0.05 (0.002)

37.2614 (1.4905)

37.11 (1.4844)

Camshaft cam height

37.0084 (1.4803)

36.86 (1.4744)

10 (0.4)

阡

10.015 (0.4006)

10.1 (0.404)

Valve rocker arm I.D.

10 (0.4)

阡

10.015 (0.4006)

10.1 (0.404)

Valve rocker arm shaft

9.975 (0.399)

阡

9.99 (0.3996)

9.9 (0.396)

O.D.

9.975 (0.399)

阡

9.99 (0.3996)

9.9 (0.396)

Rocker arm to shaft clearance

0.009 (0.0004)

阡

0.042 (0.0017)

0.1 (0.004)

4.975 (0.199)

阡

4.99 (0.1996)

4.925 (0.197)

Valve stem O.D.

4.955 (0.1982)

阡

4.97 (0.1988)

4.915 (0.1966)

5 (0.2)

阡

5.015 (0.2006)

5.03 (0.2012)

Valve guide I.D.

5 (0.2)

阡

5.015 (0.2006)

5.03 (0.2012)

Valve stem-to-guide

0.01 (0.004)

阡

0.037 (0.0015)

0.08 (0.0032)

clearance

0.03 (0.0012)

阡

0.057 (0.0023)

0.1 (0.004)

Содержание MXU 500

























































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MXU 500

Отзывы:

Похожие инструкции для MXU 500

Бренды по названию

Популярные бренды

KYMCO MXU 500, Руководство пользователя

Результаты поиска

Содержание MXU 500

Отзывы:

Похожие инструкции для MXU 500

Бренды по названию

Популярные бренды