KYMCO MXU 500 Скачать руководство пользователя

Страница: 420 / 664

.FINAL REDUCTION/

TRANSMISSION SYSTEM

11-23

MXU 500

Apply clean engine oil to the countershaft

assembly, driveshaft assembly and primary

drive shaft.

Install the primary drive shaft.
Install the countershaft and drive shaft

assemblies as a set into the left crankcase.

Apply clean engine oil to the shift cam, then

install the shift cam.

Apply clean engine oil to the gearshift fork,

sliding surface and gearshift fork pawl.

Install the lower gearshift fork into the clutch

dog (countershaft) and shift cam grooves with

its “LDB5” mark facing down.

Install the upper gearshift fork into the clutch

dog (countershaft) and shift cam grooves with

its “LDB5” mark facing up.

Drive shaft Assembly

Primary Drive Shaft Countershaft Assembly

Shift Cam

Lower Shift Fork Upper Shift Fork

Содержание MXU 500

























































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MXU 500

Отзывы:

Похожие инструкции для MXU 500

Бренды по названию

Популярные бренды

KYMCO MXU 500, Руководство пользователя

Результаты поиска

Содержание MXU 500

Отзывы:

Похожие инструкции для MXU 500

Бренды по названию

Популярные бренды