KYMCO Kymco UXV 500i Скачать руководство пользователя страница 394

Страница: 394 / 426

13. FUEL INJECTION SYSTEM

22-9

UXV500i

CHECK ENGINE LAMP (CELP)

When turning on the switch, the lamp will

be lighted for 2 seconds then off. Let

user to know the lamp is available and

connect to ECU.

But after then or during riding, if the

CELP start to blink or keep lighting, it

means something wrong with this

vehicle, you better do the further check

to find out the failure code to know

which part get trouble

There are 3 kinds of priority grade let

user to know what kind of trouble was

happened.

Priority grade 1: CELP blinks

continuously. This is the most emergent

situation like engine over heat. User

better slow down the riding and go to

dealer for checking.

Priority grade 2: CELP lights all the

time. It means components get trouble

or circuit something wrong. Do the

further check to find out the failure code

to know which part get trouble.

Priority grade 3: CELP just blinks once

suddenly and then disappear. It

sometimes just warning like the RPM

was too high in a short term.

CELP (Check Engine Lamp)

Содержание Kymco UXV 500i











































































































































































































































































































































































































































Результаты поиска

Содержание Kymco UXV 500i

Отзывы:

Бренды по названию

Популярные бренды

KYMCO Kymco UXV 500i, Руководство по обслуживанию

Результаты поиска

Содержание Kymco UXV 500i

Отзывы:

Бренды по названию

Популярные бренды